In 2026, the global isolation device market is undergoing a significant round of changes in the supply landscape. Since the end of 2025, analog chip manufacturers represented by Texas Instruments and ADI have successively initiated price increases. In March 2026, TI launched its second comprehensive price increase of the year, with increases ranging from 15% to 85%. Core product lines such as digital isolators, isolated driver chips, and power management ICs are all on the price increase list. ADI's overall price increase is about 15%, with some military-grade products reaching 30%.
Beyond price increases, lead-time issues are more prominent. Lead times for optocouplers and isolation devices have collectively stretched to more than 20 weeks, and mainstream digital isolator models have gone from a few weeks to several months. At the same time, the overall domestic localization rate in China's isolation chip market has exceeded 45%, with Novosense ranking first with a 22.8% share. Its isolated gate driver products have ranked first in China's market share for three consecutive years, with cumulative shipments exceeding 1.4 billion units.
The following sections organize some internationally popular models that are widely discussed in the market by category, and introduce corresponding Novosense solutions available for evaluation.
1. Digital Isolators
Digital isolators are the largest-volume category among isolation devices. Signal isolation in industrial PLCs, servo drives, isolated SPI/RS485, and photovoltaic inverters basically uses this type of chip.
Popular international models: ISO7721 (dual-channel, 1 forward/1 reverse), Si8621 (dual-channel), ISO7741 (quad-channel, 3 forward/1 reverse), Si8641 (quad-channel), ADUM1201 (ADI dual-channel magnetic coupler), ISO6760 (six-channel).
These categories are the areas where domestic substitution is most fully developed. Manufacturers such as Chipanalog, 3PEAK, and Rongpai all offer corresponding models on the market, giving engineers a relatively broad choice. Below are Novosense's cross-reference and key parameters in these categories.
Dual-channel — NSI8221
| Parameter/Type | ISO7721 | ISO6421 | Si8621 | ADuM1201 | NSI8221 |
| Manufacturer | TI | TI | Skyworks | ADI | Novosense |
| Isolation Technology | SiO₂ capacitor | SiO₂ capacitor | SiO₂ capacitor | iCoupler magnetic coupling | SiO₂ capacitor |
| Channel direction | 1 forward, 1 reverse | 1 forward, 1 reverse | 1 forward, 1 reverse | 1 forward, 1 reverse | 1 Forward / 1 Reverse |
| Data Rate | 100Mbps | 150Mbps | 150Mbps | 25Mbps | 150Mbps |
| CMTI | 100kV/μstyp | 200kV/μsmin | 200kV/μstyp | >25kV/μs | 250kV/μs |
| Isolation Withstand Voltage | 5kVrms(DW) | 5kVrms(DWV) | 5kVrms(SOW8) | 2.5kVrms | 5kVrms(SOW8) |
| Propagation Delay | 11nstyp | 6.2nstyp | 10.5nstyp | 20~50nsmax | 18nsmax |
| Supply Voltage Range | 2.25-5.5V | 2.25-5.5V | 2.5-5.5V | 2.7-5.5V | 2.5-5.5V |
| Package | D-8/DWV-8/DW-16 | D-8/DWV-8 | SOP8/SOW8 | SOIC-8 | SOP8/SOW8 |
| Operating Temperature | -55~125℃ | -40~125℃ | -40~125℃ | -40~125℃ | -55~125℃ |
| Refresh Mechanism | None | None | None | 5 μs watchdog | None |
In the table above, TI's ISO7721 is a mature model with a large installed base in China, while ISO6421 is its next-generation product. The pin definitions of NSI8221's SOP8/SOW8 packages are consistent with those of ISO7721's D-8/DWV-8, so it can be directly included in board-level evaluation; it outperforms 7721 in data rate and CMTI and is benchmarked against ISO6421. Note, however, that 6421's safety certification status (as stated) is planned (not all certifications obtained), whereas NSI8221 has complete safety certificates.
For isolated SPI scenarios above 50 MHz, attention should be paid to the propagation delay gap of NSI8221; its 18 ns maximum propagation delay will squeeze timing margin, so oscilloscope-measured eye diagrams are recommended. Low-speed scenarios such as UART and RS-485 are less affected. Note that ISO7721 has a DW-16 (16-pin) package version, while NSI8221 has no 16-pin package.
Si8621 (from Skyworks) is a frequently used BOM item for photovoltaic and inverter products exported overseas. It also uses capacitive isolation with no refresh mechanism, and its SOW8 package pins are compatible with NSI8221-W; typical propagation delay is better than that of NSI8221, and high-speed SPI timing must be verified at board level. NSI8221 has a wider industrial temperature range and better CMTI specifications.
The ADUM1201 uses magnetic coupling technology, with a speed of 25 Mbps and CMTI>25 kV/μs and an isolation withstand voltage of 2.5 kVrms. Although the hardware pins are compatible with the NSI8221, magnetic coupling has a 5 μs watchdog refresh mechanism, so its behavior in long-term DC level output scenarios differs from that of capacitive isolation—the NSI8221 has no refresh mechanism and can maintain DC levels indefinitely. If the original design relies on the magnetic-coupling refresh behavior, the DC static output after replacement needs to be revalidated.
Four-channel — NSI8241
| Parameter/Type | ISO7741 | ISO6441 | Si8641 | NSI8241 |
| Manufacturer | TI | TI | Skyworks | Novosense |
| Channel Direction | 3 forward, 1 reverse | 3 forward, 1 reverse | 3 forward, 1 reverse | 3 forward, 1 reverse |
| Data Rate | 100Mbps | 150Mbps | 150Mbps | 150Mbps |
| CMTI | 100kV/μs | 250kV/μs | 200kV/μs | 250kV/μs |
| Isolation Withstand Voltage | 5kVrms(DW) | 5kVrms(DW) | 5kVrms(SOW16) | 8kVrms(SOP16-600mil) |
| Propagation Delay | 10.7ns | 6.2ns | 10.5ns | <15ns |
| Supply Voltage Range | 2.25~5.5V | 2.25~5.5V | 2.5~5.5V | 2.5~5.5V |
| Package | DW-16/DBQ-16 | DW-16 | SOW16 | SOP16(300/600mil)/SSOP16 |
| Operating Temperature | -55~125℃ | -40~125℃ | -40~125℃ | -55~125℃ |
The SOP16 (300mil) package of the NSI8241 has the same pin definition as the DW-16 of the ISO7741. In PLC multi-channel SPI scenarios, the four-channel 3-forward/1-reverse configuration is the most commonly used. In terms of isolation withstand voltage, the SOP16 (600mil) package of the NSI8241 provides 8000Vrms, higher than the 5000Vrms of the ISO7741/ISO6441.
The ISO6441 is also TI's new-generation high-CMTI four-channel device, with certification planned; the NSI8241 has advantages in certification completeness and low-temperature range. The Si8641 is a high-frequency four-channel capacitive isolation device for export equipment, with pin-compatible SOW16; the NSI8241 offers higher withstand-voltage versions and wide-temperature capability, but is slightly inferior in propagation delay.
Six-Channel — NSI826x
| Parameter/Type | ISO6760 | NSI826x |
| Number of Channels | 6 | 6 |
| Data Rate | 50Mbps | 150Mbps |
| CMTI | 100kV/μs | 200kV/μs |
| Isolation Withstand Voltage | 5kVrms | 5kVrms |
| Operating temperature | -40~125℃ | -55~125℃ |
The barrier to evaluating digital isolators is low: adding a 0.1 μF bypass capacitor at each of the input and output is enough for operation. However, the bypass capacitors should be placed as close as possible to the chip's power pins; otherwise, high-frequency noise may couple into the isolation channel through the power pins. NOVOSENSE's official website provides digital isolator selection guides and application notes, covering PCB layout and bypass capacitor configuration recommendations. In addition, the NSI822x/824x series has been shipped in volume in scenarios such as industrial inverters, servo drives, and photovoltaic inverters. NOVOSENSE's digital isolators have cumulative shipments exceeding 600 million units, with sufficient mature mass-production validation.
II. Digital Isolators with Integrated Power
This category is used in isolated RS-485, isolated CAN, and industrial instruments to isolate both signals and power, eliminating the need for external discrete isolated power modules. The domestic options in this category are significantly fewer than those for pure digital isolators.
Popular international models: ISOW7841 (four-channel + integrated isolated DC-DC), ADUM5401 (isoPower magnetic coupling, 4-channel with integrated isolated power).
NOVOSENSE NSIP894x
| Parameter/Type | ISOW7841 | ADuM5401 | NSIP894x |
| Manufacturer | TI | ADI | NOVOSENSE |
| Isolation Technology | SiO₂ Capacitor | iCoupler Magnetic Coupling | SiO₂ Capacitor |
| Number of Channels | 4 | 4 | 4 |
| Integrated Isolated Power Supply | 650mW | 500mW | 500mW |
| Data Rate | 100Mbps | 150Mbps | 150Mbps |
| CMTI | 100kV/μs | >50kV/μs | 150kV/μs |
| Isolation withstand voltage | 5kVrms | 5kVrms | 5kVrms |
| Output voltage configuration | 5V/3.3V | VSEL selects 3.3V/5V | 5V/3.3V (SEL pin) |
| Load current | 130mA@5V | 100mA@5V | 100mA(5V→5V)/60mA(3.3V→3.3V) |
| Maximum operating temperature | 125℃ | 105℃ | 125℃ |
| Watchdog refresh | None | 5 μs watchdog | None |
| Protection features | Overcurrent + overtemperature | Overcurrent, thermal shutdown | Overcurrent (Hiccup) + overtemperature (165°C) |
| Package | SOIC-16 | SOIC-16 | SOW16 |
The NSIP894x uses an on-chip transformer to achieve isolated power transfer. Compared with the ISOW7841, the two have incompatible pin definitions and require board modification for evaluation; the output power is also slightly lower. When exceeding 500 mW, the combination solution of “NSI824x + discrete isolated power module” can be evaluated.
Compared with the ADUM5401, both have an output power of 500 mW, but there are three key differences: the ADUM5401 uses a magnetic-coupling solution and has a maximum temperature of only 105°C (it does not support 125°C industrial high temperature); its internal 180 MHz high-frequency oscillator is very sensitive to PCB layout EMI; and it has a 5 μs watchdog refresh, so a DC level that remains unchanged for a long time will cause abnormal output. The NSIP894x uses capacitive isolation, supports industrial high temperatures, and has no refresh mechanism. The two are also pin-incompatible, requiring a board redesign for a functional solution-level replacement.
For the NSIP894x, NOVOSENSE's official website provides an application note titled “Low-EMI Design with the NSIP8xxx Series Digital Isolators Featuring an Integrated On-Chip Transformer and Isolated DC-DC Power Supply.” If the system uses a 1500 V high-voltage bus (photovoltaic, energy storage), NOVOSENSE offers the NSIP984x-DSWWR series; the ultra-wide-body SOWW16 package increases the creepage distance from 8.15 mm to 15 mm, with an isolation withstand voltage of 7.5 kVrms, meeting the creepage-distance requirement for reinforced insulation in 1500 V systems of>the 14 mm safety requirement.
III. Isolated Gate Drivers
Drive isolation for SiC and IGBT, used in traction inverters, OBCs, PV inverters, and UPS. This category has two levels of differentiation: parameter-benchmarking solutions and functional-safety-certified solutions.
Popular international models: UCC21750 (single-channel smart driver), UCC21520 (dual-channel 4 A isolated gate driver), Si8274 (single-channel smart gate driver), NCD57000 (onsemi single-channel smart gate driver)
Single-Channel Smart Gate Driver — NSI6611ASC
| Parameters/Type | UCC21750 | Si8274 | NCD57000 | NSI6611ASC-Q1 |
| Manufacturer | TI | Skyworks | onsemi | NOVOSENSE |
| Peak Drive Current | ±10A | ±10A | Source+4A/Sink-6A | 10A |
| CMTI | 150V/ns | 150kV/μs | >100kV/μs | 150kV/μs |
| DESAT Response | 200ns | 200ns | Configurable Blanking Time | 200ns |
| Soft Turn-Off Current | 400mA | 400mA | Short-Circuit Soft Turn-Off | 400mA |
| Miller Clamp | Active | Active Miller Clamp | Active Miller Clamp with Independent CLAMP Pin | Active Miller Clamp |
| Driver-Side Voltage | 33V | 33V | Supports Positive and Negative VEE2 (Down to -9 V) | 32V |
| Isolation Withstand Voltage | 5.7kVrms | 5kVrms | 5kVrmsUL1577 | 5.7kVrms |
| ASC Protection | No | No | No | Yes |
| Fault/Ready Pin | FLT | FLT | FLT and RDY dual open-drain outputs | FLT |
| Reset function | No | None | RST reset pin | Software logic reset |
| Package | SOIC-16 | Wide-SOIC-16 | SOIC-16WB (8 mm creepage) | SOW16 |
Compared with UCC21750, the core parameters of NSI6611ASC are basically aligned. The driver-side voltage is only 1 V lower, which has no impact in most IGBT/SiC driving scenarios. NSI6611ASC integrates ASC (active short-circuit protection), specified in the datasheet as forcing a high-level output in emergency conditions, which UCC21750 does not have. If ASC is not required, NSI6651 (non-ASC version) is another evaluation option.
Si8274 has built-in DESAT and active Miller clamping; NSI6611ASC offers higher isolation voltage and ASC active short-circuit protection; the package pins allow pin-to-pin evaluation, while the DESAT threshold and fault protection logic need to be checked item by item and verified at board level.
NCD57000: a high-frequency component for UPS and photovoltaic power conversion, featuring an independent CLAMP Miller clamp pin, RDY ready output, RST hardware reset pin, and support for VEE2 negative supply down to -9 V. NOVOSENSE NSI6611ASC has no independent CLAMP pin, no hardware RST, and no RDY ready pin; this peripheral logic must be implemented in MCU software. NSI6611ASC has stronger drive current and higher isolation voltage than NCD57000. It cannot be directly pin-to-pin; functional pins differ, so a board redesign is required for evaluation, with focus on CLAMP, RDY, and RST logic.
Dual-Channel Gate Driver — NSI6602
| Parameter/Type | UCC21520 | NSI6602 |
| Channels | Dual-Channel Half-Bridge | Dual-Channel Half-Bridge |
| Peak Drive Current | ±4A | 4Asource/6Asink |
| CMTI | 150kV/μs | 150kV/μs |
| Isolation Withstand Voltage | 5.7kVrms | 5.7kVrms |
| Programmable Dead Time | Built-in | No built-in |
| Package | SOIC-16 | SOW16 |
The NSI6602 has a similar hardware pinout but lacks built-in programmable dead-time functionality. Dead-time control must be implemented in software in the external circuit, requiring board modification and evaluation.
Additional recommendation for an ASIL D functional-safety driver: NSI6911F
| Parameter/Type | NSI6911F |
| Peak drive current | 19A |
| CMTI | ±150kV/μs |
| Functional safety level | ISO26262ASILD |
| Integrated sampling | Dual-channel 12-bit isolated ADC (0.2% accuracy) |
| Safety mechanisms | More than 30 |
| Diagnostic coverage | >99% |
| Compatible platforms | 800V and above high-voltage platforms |
For scenarios such as traction inverters and OBCs that require functional safety certification, ASIL D certification itself is the threshold; this is a dimension that most parameter-benchmarking solutions cannot cover.
NOVOSENSE isolated gate driver products have ranked first in China's market share for three consecutive years. Isolated gate driver products with protection functions have been mass-produced in some new energy vehicle main drive applications and are gradually replacing optocoupler drivers in photovoltaic inverters and industrial motor drives.
IV. Isolated Sampling
Mainly includes motor phase current sampling, bus voltage sampling, and photovoltaic current detection.
Popular international models: AMC1311 (isolated voltage amplifier), AMC1301 (isolated current amplifier), and ACPL-790B (Broadcom optocoupler-based isolated sampling amplifier).
Voltage Sampling — NSI1311
| Parameter/Type | AMC1311 | NSI1311-DSWVR |
| Type | Isolated Voltage Amplifier | Isolated Voltage Amplifier |
| Input Range | 0.1-2V | 0.02-2V |
| Gain | 1 | 1 |
| Isolation Withstand Voltage | 5000Vrms | 5000Vrms |
| CMTI | 150kV/μs | 150kV/μs |
| Offset Error | ±1.5mVmax | ±1.5mVmax |
| Gain Error | ±0.3%max | ±0.3%max |
| Nonlinearity Error | ±0.04%max | ±0.04%max |
| SNR | 82dBtyp@10kHz | 82dBtyp@10kHz |
| Package | SOP-8(300mil) | SOP-8(300mil) |
The package and pinout of the NSI1311-DSWVR are identical to those of the AMC1311, with comparable performance, enabling board-level evaluation without modifying the PCB layout. For 1500 V high-voltage bus applications, NOVOSENSE also offers the NSI1311-DSWWAR in an SOP-8 (600 mil) package, with isolation withstand voltage increased to 7.5 kVrms to meet higher creepage distance requirements.
Current Sensing — NSI1300D25
| Parameter/Type | AMC1301 | ACPL-790B | NSI1300D25 |
| Manufacturer | TI | Broadcom | NOVOSENSE |
| Architecture | SiO₂ capacitive isolation amplifier | Optocoupler-based isolated sampling amplifier | SiO₂ Capacitive Isolation Amplifier |
| Input Range | ±250mV | ±250mV | ±250 mV (±50 mV version for NSI1306) |
| Gain | 8.2 | 8.2 | 8.2 |
| Isolation Withstand Voltage | 5000Vrms | 5000Vrms | 5700Vrms |
| CMTI | 150kV/μsmin | 15kV/μs | 150kV/μs |
| Offset Error | ±0.2mVmax | ±0.3mV | ±0.2mVmax |
| Gain Error | ±0.3%max | ±0.5% | ±0.3%max |
| Nonlinearity | ±0.03%max | ±0.05% | ±0.03%max |
| SNR | 86dBtyp | 72dBtyp | 86dBtyp |
| Bandwidth | 310kHz | 200kHz | 310kHz |
| Package | SOIC-8 | SO-8 | SOIC8-WB |
Compared with the AMC1301, the offset error and gain error of the NSI1300D25 are on the same order of magnitude based on datasheet nominal values; a complete accuracy benchmark must be judged according to the system accuracy requirements. The SOP8 (300mil) package has identical pin definitions, allowing pin-to-pin board-level evaluation. NOVOSENSE also offers the small-range model NSI1306, ±50 mV, gain 41.
ACPL-790B: many existing devices use optocoupler-based sampling amplifiers, but they suffer from LED aging drift; CMTI is only 15 kV/μs, and bandwidth is 200 kHz; the NSI1300D25 has no optocoupler aging issue and is superior in most specifications, making it a solution-level board redesign replacement.
NOVOSENSE isolated sampling products have been widely used in industrial transmitters, inverters, PLCs, servo systems, and other industrial control applications. Application notes for isolated amplifiers are also provided, covering input filter design and other topics to help engineers get started quickly.
V. High-Speed SOP-5Optocouplers (Digital Isolator Upgrade/Replacement Scenarios)
Popular international models: TLP109 (Toshiba), ACPL-M61L (Broadcom).
NOVOSENSE NSI72xx
| Parameter/Type | TLP109 | ACPL‑M61L | NSI72xx |
| Manufacturer | Toshiba | Broadcom | NOVOSENSE |
| Device Type | High-Speed Optocoupler | SOP-5 CMOS-Output High-Speed Optocoupler | SOP-5 Digital Isolator |
| Data Rate | 1Mbps | 10MBd | DC‑150Mbps |
| Package | SOP‑5 | SOP‑5 | SOP‑5 |
| Operating Temperature | ‑55~+100℃ | ‑40~+110℃ | ‑40~+125℃ |
| CMTI | — | — | 100kV/μs |
TLP109 and ACPL-M61L are both high-speed optocouplers in SOP-5 packages, and the NSI72xx is pin-to-pin compatible at the hardware package level. However, the peripheral resistor network parameters for driving the original optocoupler LED cannot be copied directly and require re-tuning. The advantage is eliminating the risk of optocoupler LED aging failure, making it suitable for upgrading long-term high-reliability equipment.
VI. Isolated Interfaces
Isolated RS-485 and isolated CAN, standard in industrial buses and automotive communication.
Popular international models: ISO1042 (isolated CAN FD), ISO3082 (isolated RS-485, 20 Mbps), ADM2687E (isolated RS-485 with integrated power isolation).
Isolated CAN — NSI1042
| Parameter/Type | ISO1042 | NSI1042 |
| Type | Isolated CAN | Isolated CAN |
| Data Rate | 5Mbps(CANFD) | 5Mbps(CANFD) |
| Isolation Withstand Voltage | 5000Vrms | 5000Vrms |
| Loop Delay | 210ns | <220ns |
| Bus Fault Protection | ‑70V~+70V | ‑70V~+70V |
| Package | SOIC‑8 | SOP8 |
The package and pin definitions of the NSI1042 are identical to those of the ISO1042, enabling board-level evaluation without modifying the PCB layout, and it is compatible with the ISO11898-2 standard.
Isolated RS-485 — NSI83085E/83086E
| Parameter/Type | ISO3082 | NSI83085E | NSI83086E |
| Type | Isolated RS-485 Half-Duplex | Isolated RS-485 Half-Duplex | Isolated RS-485 Full-Duplex |
| Data Rate | 20Mbps | 500kbps | 16Mbps |
| Isolation Withstand Voltage | 5kVrms | 5kVrms | 5kVrms |
| ESD Protection | ±15kVHBM | ±16kV | ±16kV |
| Bus Load | 1/8 unit (256 nodes) | 1/8 unit (256 nodes) | 1/8 unit (256 nodes) |
The NSI83085E is used for half-duplex RS-485 isolation, with a maximum of 500 kbps. Its low slew rate design reduces EMI radiation and reflections caused by improper termination matching. The NSI83086E is used for full-duplex RS-485 isolation, with a maximum of 16 Mbps. Most industrial RS-485 applications operate below 10 Mbps, and the NSI83086E can cover most scenarios; if the system requires 20 Mbps, the feasibility of reducing the speed needs to be evaluated.
Summary
The above has reviewed, by category, some international models that are widely discussed in the market and their corresponding NOVOSENSE solutions. For pure digital isolators, isolated sampling, and isolated interface categories, domestic options are already relatively plentiful; NOVOSENSE and corresponding models in the same category are at the same order of magnitude in core parameters, with differences mainly concentrated in individual metrics such as propagation delay, which usually do not matter in low-speed general-purpose scenarios.
Digital isolators with integrated power and functional-safety isolated drivers are two categories worthy of particular attention. Domestic alternatives corresponding to the ISOW7841 are relatively scarce in the market, and the NSIP894x is currently one of the few four-channel digital isolator solutions with integrated isolated DC-DC; the NSI6911F, as China's first isolated gate driver chip certified by TÜV Rheinland to ISO 26262 ASIL D, provides an option for main-drive inverter and OBC scenarios requiring functional-safety certification that parameter-benchmarking alternatives cannot cover. NOVOSENSE also provides application notes and reference designs for various categories on its official website, covering low-EMI design, isolated sampling circuit design, RS-485 isolation circuit reference design, etc., which can be referenced during the selection and evaluation stage.
Disclaimer: The product parameters involved in this article all come from the datasheets publicly released by the respective manufacturers; the data are nominal values from the datasheets. For specific selection decisions, please refer to actual test verification and the manufacturer's latest datasheet. The models listed in this article are not necessarily the latest generation products; models with better performance may exist on the official website.
If you need in-depth details on a specific NOVOSENSE model and to request samples, please contact: sales@chiplinkstech.com; Mr. Chen, 13924675549.
Appendix: Overview Table
| International Model | NOVOSENSE Equivalent | Parameter coverage status | Key selection decision points |
| ISO7721 | NSI8221 | Parameter coverage | Evaluate directly for low-speed scenarios; measure propagation delay for SPI scenarios; the 16-pin DW is not replaceable |
| ISO6421 | NSI8221 | Parameter coverage | Verify ESD, -55°C low-temperature performance, and safety compliance certificates; measure timing for high-speed SPI |
| Si8621 | NSI8221 | Parameter coverage | The Si8621 has better propagation delay; pin-compatible—verify low-temperature performance and timing |
| ADUM1201 | NSI8221 | Parameter coverage | Magnetic isolator model; verify refresh behavior in static DC scenarios; data rate/CMTI are upgrade items |
| ISO7741 | NSI8241 | Parameter coverage | Four channels, 3 forward and 1 reverse; commonly used for multi-channel SPI in PLCs |
| ISO6441 | NSI8241 | Parameter coverage | Check safety compliance and low-temperature limits; measure timing margin for high-speed SPI |
| Si8641 | NSI8241 | Parameter coverage | Si8641 offers better propagation delay, is pin-compatible, and has an optional high withstand voltage rating |
| ISO6760 | NSI826x | Parameter coverage | Six-channel, CMTI 200 kV/μs |
| ISOW7841 | NSIP894x | Functional solution level | Verify whether the total load of the isolated power supply exceeds 500 mW; if the pins are incompatible, the board must be modified |
| ADUM5401 | NSIP894x | Functional solution level | Magnetic-coupling watchdog risk; different upper temperature limits (105°C limit); PCB modification required |
| UCC21750 | NSI6611ASC | Parameter coverage | Preferred when ASC function is required; if not required, NSI6651 can be selected |
| Si8274 | NSI6611ASC | Parameter coverage | Frequently used part in export projects; verify fault-protection thresholds and perform board-level validation |
| NCD57000 | NSI6611ASC | Functional solution level | onsemi has CLAMP, RDY, and RST hardware pins; NOVOSENSE has no such hardware pins and implements them in software, requiring board-change evaluation |
| UCC21520 | NSI6602 | Functional solution level | No built-in programmable dead time; external circuitry must be modified |
| AMC1311 | NSI1311 | Parameter coverage | Supply is tight for some packages; note package differences indicated by part-number suffixes, and evaluate accuracy metrics at board level |
| AMC1301 | NSI1300D25 | Comparable parameters | Item-by-item comparison of accuracy metrics with board-level verification; NSI1306 evaluated at a small ±50 mV range |
| ACPL‑790B | NSI1300D25 | Functional solution level | Optocoupler architecture; pin-incompatible, board redesign required; avoids LED aging drift |
| TLP109 | NSI72xx | Pin-to-pin evaluation | SOP-5 package; external resistor retuning required |
| ACPL‑M61L | NSI72xx | Pin-to-pin evaluation | SOP-5 package; external circuit parameters require retuning |
| ISO1042 | NSI1042 | Parameter coverage | Consistent package; reference design can be reused directly |
| ISO3082 | NSI83085E/NSI83086E | Parameter coverage | 500 kbps half-duplex / 16 Mbps full-duplex; verify system rate |
| NOVOSENSE supplement | NSIP984x‑DSWWR | 1500 V extension | Creepage distance 15 mm, meeting PV energy storage safety standards |
| NOVOSENSE supplement | NSI6911F | Certification threshold coverage | China's first ASIL D isolated driver |

Sample request attached

WeChat Official Account