0755-82557621 sales@chiplinkstech.com Mon–Fri 09:00–18:00 (UTC+8)
Precision motion control · Components and solutions

TMC4361—Closed-Loop Stepper Motor Drive Solution

Closed-loop control of stepper motors achieves features comparable to and even surpassing those of servo motors. For motor control applications requiring high efficiency, higher precision, and absolute reliability, we recommend a more cost-effective drive solution that is sensorless and minimizes size. As we all know, without feedback on a stepper motor, high-speed operation, such as sudden loads [...]

2022-07-12 方案应用
TMC4361—步进电机闭环驱动方案

Closed-loop control of stepper motors achieves features comparable to and surpassing those of servo motors. In motor control, if you want high efficiency, higher precision, and absolute reliability, we recommend a more cost-effective drive solution that is sensorless and minimizes size.

As we all know, when a stepper motor has no feedback, high-speed operation, such as sudden loads or increased load, may affect the normal operation of the stepper motor, resulting in step loss. In addition to high speed and load, motor acceleration/deceleration and system inertia can also cause step loss. This is a drawback of open-loop stepper motor control.

TMC4361模块

The advantage of open-loop control is low cost, and it can meet the needs of most industries. In addition, Trinamic's driver chips have strong anti-interference capability and are normally unaffected, and they can achieve position control without feedback. However, under load or other influences, the step command may differ from the actual steps, affecting precision and efficiency. Especially in the 3D printer industry, precision is particularly important, and previous drive/control methods achieved high precision by controlling speed. So is there a motion control solution for higher precision and high speed? The answer is: yes!

Selection of cost-effective Trinamic closed-loop stepper motor drive solutions

TMC4361+TMC2130/TMC5130 (low power)

TMC4361+TMC2160/TMC5160 (high power)

The TMC4361 is a closed-loop positioning IC that integrates a closed-loop algorithm and current control, plus a ramp (curve acceleration/deceleration) generator.

曲线加减速

Closed-loop control of stepper motors can perfectly solve this problem. We can understand closed-loop control as 'closing the loop,' because in our previous drive control method, one pulse causes the motor to move one step; when we want the motor to move 1000 steps, we naturally assume that sending 1000 pulses is sufficient.

In open-loop control, when the motor is affected by load during motion control, it is possible that 1000 pulses are sent but the motor moves only 998 steps, losing 2 steps in the process, so the motor does not complete the intended movement.

In closed-loop control, throughout the entire motion process, if it is detected that 1000 pulses were sent but the motor moved only 998 steps, a command will be fed back to the MCU, and the MCU will issue two additional pulses to make the motor move two more steps, completing the 1000-step command.

Therefore, closed-loop control of stepper motors includes key technologies such as step verification, lost-step prevention, stall detection, and torque control. It offers better stability and higher precision, along with high response and high speed.

步进闭环控制

Advantages of the TMC4361 closed-loop stepper motor drive solution

1. Supports absolute encoders
Incremental or absolute encoders are selectable, making design more convenient for engineers.

2. S-curve ramp

3. Supports emergency stop, overshoot-preventing emergency stop, and frequent start/stop

4. Acceleration/deceleration control at any point

5. No gain tuning required, no jitter at standstill

6. Quiet operation, no jitter at low speed

7. High speed, high efficiency, high response

Unlike servo controllers, Trinamic's closed-loop stepper motor drive solution is more compact. The MCU, driver, and interface are integrated into one module. Not only is wiring simple, but after-sales maintenance is also very convenient. In addition, signals are less susceptible to magnetic field interference, making closed-loop detection more precise. This solution is suitable for higher-precision 3D printer industry applications and is also a cost-effective control solution.

← Back to Solutions