0755-82557621 sales@chiplinkstech.com Mon–Fri 09:00–18:00 (UTC+8)
Precision motion control · Components and solutions

Roundup of Popular Isolation Device Models from International Vendors — Evaluation of Novosense's Domestic Solutions

In 2026, the global isolation device market is undergoing a significant shift in the supply landscape. Starting in late 2025, analog chipmakers represented by Texas Instruments and ADI began raising prices successively. In March 2026, TI launched its second broad price increase of the year, with increases of 15% to 85%; core product lines such as digital isolators, isolated driver chips, and power management ICs were all included in the price increase list. [...]

2026-10-08 Solution Applications
国际厂商热门隔离器件型号盘点——纳芯微国产方案评估

In 2026, the global isolation device market is undergoing a significant round of changes in the supply landscape. Since the end of 2025, analog chip manufacturers represented by Texas Instruments and ADI have successively initiated price increases. In March 2026, TI launched its second comprehensive price increase of the year, with increases ranging from 15% to 85%. Core product lines such as digital isolators, isolated driver chips, and power management ICs are all on the price increase list. ADI's overall price increase is about 15%, with some military-grade products reaching 30%.

Beyond price increases, lead-time issues are more prominent. Lead times for optocouplers and isolation devices have collectively stretched to more than 20 weeks, and mainstream digital isolator models have gone from a few weeks to several months. At the same time, the overall domestic localization rate in China's isolation chip market has exceeded 45%, with Novosense ranking first with a 22.8% share. Its isolated gate driver products have ranked first in China's market share for three consecutive years, with cumulative shipments exceeding 1.4 billion units.

The following sections organize some internationally popular models that are widely discussed in the market by category, and introduce corresponding Novosense solutions available for evaluation.

1. Digital Isolators

Digital isolators are the largest-volume category among isolation devices. Signal isolation in industrial PLCs, servo drives, isolated SPI/RS485, and photovoltaic inverters basically uses this type of chip.

Popular international models: ISO7721 (dual-channel, 1 forward/1 reverse), Si8621 (dual-channel), ISO7741 (quad-channel, 3 forward/1 reverse), Si8641 (quad-channel), ADUM1201 (ADI dual-channel magnetic coupler), ISO6760 (six-channel).

These categories are the areas where domestic substitution is most fully developed. Manufacturers such as Chipanalog, 3PEAK, and Rongpai all offer corresponding models on the market, giving engineers a relatively broad choice. Below are Novosense's cross-reference and key parameters in these categories.

Dual-channel — NSI8221

Parameter/Type ISO7721 ISO6421 Si8621 ADuM1201 NSI8221
Manufacturer TI TI Skyworks ADI Novosense
Isolation Technology SiO₂ capacitor SiO₂ capacitor SiO₂ capacitor iCoupler magnetic coupling SiO₂ capacitor
Channel direction 1 forward, 1 reverse 1 forward, 1 reverse 1 forward, 1 reverse 1 forward, 1 reverse 1 Forward / 1 Reverse
Data Rate 100Mbps 150Mbps 150Mbps 25Mbps 150Mbps
CMTI 100kV/μstyp 200kV/μsmin 200kV/μstyp >25kV/μs 250kV/μs
Isolation Withstand Voltage 5kVrms(DW) 5kVrms(DWV) 5kVrms(SOW8) 2.5kVrms 5kVrms(SOW8)
Propagation Delay 11nstyp 6.2nstyp 10.5nstyp 20~50nsmax 18nsmax
Supply Voltage Range 2.25-5.5V 2.25-5.5V 2.5-5.5V 2.7-5.5V 2.5-5.5V
Package D-8/DWV-8/DW-16 D-8/DWV-8 SOP8/SOW8 SOIC-8 SOP8/SOW8
Operating Temperature -55~125℃ -40~125℃ -40~125℃ -40~125℃ -55~125℃
Refresh Mechanism None None None 5 μs watchdog None

In the table above, TI's ISO7721 is a mature model with a large installed base in China, while ISO6421 is its next-generation product. The pin definitions of NSI8221's SOP8/SOW8 packages are consistent with those of ISO7721's D-8/DWV-8, so it can be directly included in board-level evaluation; it outperforms 7721 in data rate and CMTI and is benchmarked against ISO6421. Note, however, that 6421's safety certification status (as stated) is planned (not all certifications obtained), whereas NSI8221 has complete safety certificates.

For isolated SPI scenarios above 50 MHz, attention should be paid to the propagation delay gap of NSI8221; its 18 ns maximum propagation delay will squeeze timing margin, so oscilloscope-measured eye diagrams are recommended. Low-speed scenarios such as UART and RS-485 are less affected. Note that ISO7721 has a DW-16 (16-pin) package version, while NSI8221 has no 16-pin package.

Si8621 (from Skyworks) is a frequently used BOM item for photovoltaic and inverter products exported overseas. It also uses capacitive isolation with no refresh mechanism, and its SOW8 package pins are compatible with NSI8221-W; typical propagation delay is better than that of NSI8221, and high-speed SPI timing must be verified at board level. NSI8221 has a wider industrial temperature range and better CMTI specifications.

The ADUM1201 uses magnetic coupling technology, with a speed of 25 Mbps and CMTI>25 kV/μs and an isolation withstand voltage of 2.5 kVrms. Although the hardware pins are compatible with the NSI8221, magnetic coupling has a 5 μs watchdog refresh mechanism, so its behavior in long-term DC level output scenarios differs from that of capacitive isolation—the NSI8221 has no refresh mechanism and can maintain DC levels indefinitely. If the original design relies on the magnetic-coupling refresh behavior, the DC static output after replacement needs to be revalidated.

Four-channel — NSI8241

Parameter/Type ISO7741 ISO6441 Si8641 NSI8241
Manufacturer TI TI Skyworks Novosense
Channel Direction 3 forward, 1 reverse 3 forward, 1 reverse 3 forward, 1 reverse 3 forward, 1 reverse
Data Rate 100Mbps 150Mbps 150Mbps 150Mbps
CMTI 100kV/μs 250kV/μs 200kV/μs 250kV/μs
Isolation Withstand Voltage 5kVrms(DW) 5kVrms(DW) 5kVrms(SOW16) 8kVrms(SOP16-600mil)
Propagation Delay 10.7ns 6.2ns 10.5ns <15ns
Supply Voltage Range 2.25~5.5V 2.25~5.5V 2.5~5.5V 2.5~5.5V
Package DW-16/DBQ-16 DW-16 SOW16 SOP16(300/600mil)/SSOP16
Operating Temperature -55~125℃ -40~125℃ -40~125℃ -55~125℃

The SOP16 (300mil) package of the NSI8241 has the same pin definition as the DW-16 of the ISO7741. In PLC multi-channel SPI scenarios, the four-channel 3-forward/1-reverse configuration is the most commonly used. In terms of isolation withstand voltage, the SOP16 (600mil) package of the NSI8241 provides 8000Vrms, higher than the 5000Vrms of the ISO7741/ISO6441.

The ISO6441 is also TI's new-generation high-CMTI four-channel device, with certification planned; the NSI8241 has advantages in certification completeness and low-temperature range. The Si8641 is a high-frequency four-channel capacitive isolation device for export equipment, with pin-compatible SOW16; the NSI8241 offers higher withstand-voltage versions and wide-temperature capability, but is slightly inferior in propagation delay.

Six-Channel — NSI826x

Parameter/Type ISO6760 NSI826x
Number of Channels 6 6
Data Rate 50Mbps 150Mbps
CMTI 100kV/μs 200kV/μs
Isolation Withstand Voltage 5kVrms 5kVrms
Operating temperature -40~125℃ -55~125℃

The barrier to evaluating digital isolators is low: adding a 0.1 μF bypass capacitor at each of the input and output is enough for operation. However, the bypass capacitors should be placed as close as possible to the chip's power pins; otherwise, high-frequency noise may couple into the isolation channel through the power pins. NOVOSENSE's official website provides digital isolator selection guides and application notes, covering PCB layout and bypass capacitor configuration recommendations. In addition, the NSI822x/824x series has been shipped in volume in scenarios such as industrial inverters, servo drives, and photovoltaic inverters. NOVOSENSE's digital isolators have cumulative shipments exceeding 600 million units, with sufficient mature mass-production validation.

II. Digital Isolators with Integrated Power

This category is used in isolated RS-485, isolated CAN, and industrial instruments to isolate both signals and power, eliminating the need for external discrete isolated power modules. The domestic options in this category are significantly fewer than those for pure digital isolators.

Popular international models: ISOW7841 (four-channel + integrated isolated DC-DC), ADUM5401 (isoPower magnetic coupling, 4-channel with integrated isolated power).

NOVOSENSE NSIP894x

Parameter/Type ISOW7841 ADuM5401 NSIP894x
Manufacturer TI ADI NOVOSENSE
Isolation Technology SiO₂ Capacitor iCoupler Magnetic Coupling SiO₂ Capacitor
Number of Channels 4 4 4
Integrated Isolated Power Supply 650mW 500mW 500mW
Data Rate 100Mbps 150Mbps 150Mbps
CMTI 100kV/μs >50kV/μs 150kV/μs
Isolation withstand voltage 5kVrms 5kVrms 5kVrms
Output voltage configuration 5V/3.3V VSEL selects 3.3V/5V 5V/3.3V (SEL pin)
Load current 130mA@5V 100mA@5V 100mA(5V→5V)/60mA(3.3V→3.3V)
Maximum operating temperature 125℃ 105℃ 125℃
Watchdog refresh None 5 μs watchdog None
Protection features Overcurrent + overtemperature Overcurrent, thermal shutdown Overcurrent (Hiccup) + overtemperature (165°C)
Package SOIC-16 SOIC-16 SOW16

The NSIP894x uses an on-chip transformer to achieve isolated power transfer. Compared with the ISOW7841, the two have incompatible pin definitions and require board modification for evaluation; the output power is also slightly lower. When exceeding 500 mW, the combination solution of “NSI824x + discrete isolated power module” can be evaluated.

Compared with the ADUM5401, both have an output power of 500 mW, but there are three key differences: the ADUM5401 uses a magnetic-coupling solution and has a maximum temperature of only 105°C (it does not support 125°C industrial high temperature); its internal 180 MHz high-frequency oscillator is very sensitive to PCB layout EMI; and it has a 5 μs watchdog refresh, so a DC level that remains unchanged for a long time will cause abnormal output. The NSIP894x uses capacitive isolation, supports industrial high temperatures, and has no refresh mechanism. The two are also pin-incompatible, requiring a board redesign for a functional solution-level replacement.

For the NSIP894x, NOVOSENSE's official website provides an application note titled “Low-EMI Design with the NSIP8xxx Series Digital Isolators Featuring an Integrated On-Chip Transformer and Isolated DC-DC Power Supply.” If the system uses a 1500 V high-voltage bus (photovoltaic, energy storage), NOVOSENSE offers the NSIP984x-DSWWR series; the ultra-wide-body SOWW16 package increases the creepage distance from 8.15 mm to 15 mm, with an isolation withstand voltage of 7.5 kVrms, meeting the creepage-distance requirement for reinforced insulation in 1500 V systems of>the 14 mm safety requirement.

III. Isolated Gate Drivers

Drive isolation for SiC and IGBT, used in traction inverters, OBCs, PV inverters, and UPS. This category has two levels of differentiation: parameter-benchmarking solutions and functional-safety-certified solutions.

Popular international models: UCC21750 (single-channel smart driver), UCC21520 (dual-channel 4 A isolated gate driver), Si8274 (single-channel smart gate driver), NCD57000 (onsemi single-channel smart gate driver)

Single-Channel Smart Gate Driver — NSI6611ASC

Parameters/Type UCC21750 Si8274 NCD57000 NSI6611ASC-Q1
Manufacturer TI Skyworks onsemi NOVOSENSE
Peak Drive Current ±10A ±10A Source+4A/Sink-6A 10A
CMTI 150V/ns 150kV/μs >100kV/μs 150kV/μs
DESAT Response 200ns 200ns Configurable Blanking Time 200ns
Soft Turn-Off Current 400mA 400mA Short-Circuit Soft Turn-Off 400mA
Miller Clamp Active Active Miller Clamp Active Miller Clamp with Independent CLAMP Pin Active Miller Clamp
Driver-Side Voltage 33V 33V Supports Positive and Negative VEE2 (Down to -9 V) 32V
Isolation Withstand Voltage 5.7kVrms 5kVrms 5kVrmsUL1577 5.7kVrms
ASC Protection No No No Yes
Fault/Ready Pin FLT FLT FLT and RDY dual open-drain outputs FLT
Reset function No None RST reset pin Software logic reset
Package SOIC-16 Wide-SOIC-16 SOIC-16WB (8 mm creepage) SOW16

Compared with UCC21750, the core parameters of NSI6611ASC are basically aligned. The driver-side voltage is only 1 V lower, which has no impact in most IGBT/SiC driving scenarios. NSI6611ASC integrates ASC (active short-circuit protection), specified in the datasheet as forcing a high-level output in emergency conditions, which UCC21750 does not have. If ASC is not required, NSI6651 (non-ASC version) is another evaluation option.

Si8274 has built-in DESAT and active Miller clamping; NSI6611ASC offers higher isolation voltage and ASC active short-circuit protection; the package pins allow pin-to-pin evaluation, while the DESAT threshold and fault protection logic need to be checked item by item and verified at board level.

NCD57000: a high-frequency component for UPS and photovoltaic power conversion, featuring an independent CLAMP Miller clamp pin, RDY ready output, RST hardware reset pin, and support for VEE2 negative supply down to -9 V. NOVOSENSE NSI6611ASC has no independent CLAMP pin, no hardware RST, and no RDY ready pin; this peripheral logic must be implemented in MCU software. NSI6611ASC has stronger drive current and higher isolation voltage than NCD57000. It cannot be directly pin-to-pin; functional pins differ, so a board redesign is required for evaluation, with focus on CLAMP, RDY, and RST logic.

Dual-Channel Gate Driver — NSI6602

Parameter/Type UCC21520 NSI6602
Channels Dual-Channel Half-Bridge Dual-Channel Half-Bridge
Peak Drive Current ±4A 4Asource/6Asink
CMTI 150kV/μs 150kV/μs
Isolation Withstand Voltage 5.7kVrms 5.7kVrms
Programmable Dead Time Built-in No built-in
Package SOIC-16 SOW16

The NSI6602 has a similar hardware pinout but lacks built-in programmable dead-time functionality. Dead-time control must be implemented in software in the external circuit, requiring board modification and evaluation.

Additional recommendation for an ASIL D functional-safety driver: NSI6911F

Parameter/Type NSI6911F
Peak drive current 19A
CMTI ±150kV/μs
Functional safety level ISO26262ASILD
Integrated sampling Dual-channel 12-bit isolated ADC (0.2% accuracy)
Safety mechanisms More than 30
Diagnostic coverage >99%
Compatible platforms 800V and above high-voltage platforms

For scenarios such as traction inverters and OBCs that require functional safety certification, ASIL D certification itself is the threshold; this is a dimension that most parameter-benchmarking solutions cannot cover.

NOVOSENSE isolated gate driver products have ranked first in China's market share for three consecutive years. Isolated gate driver products with protection functions have been mass-produced in some new energy vehicle main drive applications and are gradually replacing optocoupler drivers in photovoltaic inverters and industrial motor drives.

IV. Isolated Sampling

Mainly includes motor phase current sampling, bus voltage sampling, and photovoltaic current detection.

Popular international models: AMC1311 (isolated voltage amplifier), AMC1301 (isolated current amplifier), and ACPL-790B (Broadcom optocoupler-based isolated sampling amplifier).

Voltage Sampling — NSI1311

Parameter/Type AMC1311 NSI1311-DSWVR
Type Isolated Voltage Amplifier Isolated Voltage Amplifier
Input Range 0.1-2V 0.02-2V
Gain 1 1
Isolation Withstand Voltage 5000Vrms 5000Vrms
CMTI 150kV/μs 150kV/μs
Offset Error ±1.5mVmax ±1.5mVmax
Gain Error ±0.3%max ±0.3%max
Nonlinearity Error ±0.04%max ±0.04%max
SNR 82dBtyp@10kHz 82dBtyp@10kHz
Package SOP-8(300mil) SOP-8(300mil)

The package and pinout of the NSI1311-DSWVR are identical to those of the AMC1311, with comparable performance, enabling board-level evaluation without modifying the PCB layout. For 1500 V high-voltage bus applications, NOVOSENSE also offers the NSI1311-DSWWAR in an SOP-8 (600 mil) package, with isolation withstand voltage increased to 7.5 kVrms to meet higher creepage distance requirements.

Current Sensing — NSI1300D25

Parameter/Type AMC1301 ACPL-790B NSI1300D25
Manufacturer TI Broadcom NOVOSENSE
Architecture SiO₂ capacitive isolation amplifier Optocoupler-based isolated sampling amplifier SiO₂ Capacitive Isolation Amplifier
Input Range ±250mV ±250mV ±250 mV (±50 mV version for NSI1306)
Gain 8.2 8.2 8.2
Isolation Withstand Voltage 5000Vrms 5000Vrms 5700Vrms
CMTI 150kV/μsmin 15kV/μs 150kV/μs
Offset Error ±0.2mVmax ±0.3mV ±0.2mVmax
Gain Error ±0.3%max ±0.5% ±0.3%max
Nonlinearity ±0.03%max ±0.05% ±0.03%max
SNR 86dBtyp 72dBtyp 86dBtyp
Bandwidth 310kHz 200kHz 310kHz
Package SOIC-8 SO-8 SOIC8-WB

Compared with the AMC1301, the offset error and gain error of the NSI1300D25 are on the same order of magnitude based on datasheet nominal values; a complete accuracy benchmark must be judged according to the system accuracy requirements. The SOP8 (300mil) package has identical pin definitions, allowing pin-to-pin board-level evaluation. NOVOSENSE also offers the small-range model NSI1306, ±50 mV, gain 41.

ACPL-790B: many existing devices use optocoupler-based sampling amplifiers, but they suffer from LED aging drift; CMTI is only 15 kV/μs, and bandwidth is 200 kHz; the NSI1300D25 has no optocoupler aging issue and is superior in most specifications, making it a solution-level board redesign replacement.

NOVOSENSE isolated sampling products have been widely used in industrial transmitters, inverters, PLCs, servo systems, and other industrial control applications. Application notes for isolated amplifiers are also provided, covering input filter design and other topics to help engineers get started quickly.

V. High-Speed SOP-5Optocouplers (Digital Isolator Upgrade/Replacement Scenarios)

Popular international models: TLP109 (Toshiba), ACPL-M61L (Broadcom).

NOVOSENSE NSI72xx

Parameter/Type TLP109 ACPL‑M61L NSI72xx
Manufacturer Toshiba Broadcom NOVOSENSE
Device Type High-Speed Optocoupler SOP-5 CMOS-Output High-Speed Optocoupler SOP-5 Digital Isolator
Data Rate 1Mbps 10MBd DC‑150Mbps
Package SOP‑5 SOP‑5 SOP‑5
Operating Temperature ‑55~+100℃ ‑40~+110℃ ‑40~+125℃
CMTI — — 100kV/μs

TLP109 and ACPL-M61L are both high-speed optocouplers in SOP-5 packages, and the NSI72xx is pin-to-pin compatible at the hardware package level. However, the peripheral resistor network parameters for driving the original optocoupler LED cannot be copied directly and require re-tuning. The advantage is eliminating the risk of optocoupler LED aging failure, making it suitable for upgrading long-term high-reliability equipment.

VI. Isolated Interfaces

Isolated RS-485 and isolated CAN, standard in industrial buses and automotive communication.

Popular international models: ISO1042 (isolated CAN FD), ISO3082 (isolated RS-485, 20 Mbps), ADM2687E (isolated RS-485 with integrated power isolation).

Isolated CAN — NSI1042

Parameter/Type ISO1042 NSI1042
Type Isolated CAN Isolated CAN
Data Rate 5Mbps(CANFD) 5Mbps(CANFD)
Isolation Withstand Voltage 5000Vrms 5000Vrms
Loop Delay 210ns <220ns
Bus Fault Protection ‑70V~+70V ‑70V~+70V
Package SOIC‑8 SOP8

The package and pin definitions of the NSI1042 are identical to those of the ISO1042, enabling board-level evaluation without modifying the PCB layout, and it is compatible with the ISO11898-2 standard.

Isolated RS-485 — NSI83085E/83086E

Parameter/Type ISO3082 NSI83085E NSI83086E
Type Isolated RS-485 Half-Duplex Isolated RS-485 Half-Duplex Isolated RS-485 Full-Duplex
Data Rate 20Mbps 500kbps 16Mbps
Isolation Withstand Voltage 5kVrms 5kVrms 5kVrms
ESD Protection ±15kVHBM ±16kV ±16kV
Bus Load 1/8 unit (256 nodes) 1/8 unit (256 nodes) 1/8 unit (256 nodes)

The NSI83085E is used for half-duplex RS-485 isolation, with a maximum of 500 kbps. Its low slew rate design reduces EMI radiation and reflections caused by improper termination matching. The NSI83086E is used for full-duplex RS-485 isolation, with a maximum of 16 Mbps. Most industrial RS-485 applications operate below 10 Mbps, and the NSI83086E can cover most scenarios; if the system requires 20 Mbps, the feasibility of reducing the speed needs to be evaluated.

Summary

The above has reviewed, by category, some international models that are widely discussed in the market and their corresponding NOVOSENSE solutions. For pure digital isolators, isolated sampling, and isolated interface categories, domestic options are already relatively plentiful; NOVOSENSE and corresponding models in the same category are at the same order of magnitude in core parameters, with differences mainly concentrated in individual metrics such as propagation delay, which usually do not matter in low-speed general-purpose scenarios.

Digital isolators with integrated power and functional-safety isolated drivers are two categories worthy of particular attention. Domestic alternatives corresponding to the ISOW7841 are relatively scarce in the market, and the NSIP894x is currently one of the few four-channel digital isolator solutions with integrated isolated DC-DC; the NSI6911F, as China's first isolated gate driver chip certified by TÜV Rheinland to ISO 26262 ASIL D, provides an option for main-drive inverter and OBC scenarios requiring functional-safety certification that parameter-benchmarking alternatives cannot cover. NOVOSENSE also provides application notes and reference designs for various categories on its official website, covering low-EMI design, isolated sampling circuit design, RS-485 isolation circuit reference design, etc., which can be referenced during the selection and evaluation stage.

Disclaimer: The product parameters involved in this article all come from the datasheets publicly released by the respective manufacturers; the data are nominal values from the datasheets. For specific selection decisions, please refer to actual test verification and the manufacturer's latest datasheet. The models listed in this article are not necessarily the latest generation products; models with better performance may exist on the official website.

If you need in-depth details on a specific NOVOSENSE model and to request samples, please contact: sales@chiplinkstech.com; Mr. Chen, 13924675549.

Appendix: Overview Table

International Model NOVOSENSE Equivalent Parameter coverage status Key selection decision points
ISO7721 NSI8221 Parameter coverage Evaluate directly for low-speed scenarios; measure propagation delay for SPI scenarios; the 16-pin DW is not replaceable
ISO6421 NSI8221 Parameter coverage Verify ESD, -55°C low-temperature performance, and safety compliance certificates; measure timing for high-speed SPI
Si8621 NSI8221 Parameter coverage The Si8621 has better propagation delay; pin-compatible—verify low-temperature performance and timing
ADUM1201 NSI8221 Parameter coverage Magnetic isolator model; verify refresh behavior in static DC scenarios; data rate/CMTI are upgrade items
ISO7741 NSI8241 Parameter coverage Four channels, 3 forward and 1 reverse; commonly used for multi-channel SPI in PLCs
ISO6441 NSI8241 Parameter coverage Check safety compliance and low-temperature limits; measure timing margin for high-speed SPI
Si8641 NSI8241 Parameter coverage Si8641 offers better propagation delay, is pin-compatible, and has an optional high withstand voltage rating
ISO6760 NSI826x Parameter coverage Six-channel, CMTI 200 kV/μs
ISOW7841 NSIP894x Functional solution level Verify whether the total load of the isolated power supply exceeds 500 mW; if the pins are incompatible, the board must be modified
ADUM5401 NSIP894x Functional solution level Magnetic-coupling watchdog risk; different upper temperature limits (105°C limit); PCB modification required
UCC21750 NSI6611ASC Parameter coverage Preferred when ASC function is required; if not required, NSI6651 can be selected
Si8274 NSI6611ASC Parameter coverage Frequently used part in export projects; verify fault-protection thresholds and perform board-level validation
NCD57000 NSI6611ASC Functional solution level onsemi has CLAMP, RDY, and RST hardware pins; NOVOSENSE has no such hardware pins and implements them in software, requiring board-change evaluation
UCC21520 NSI6602 Functional solution level No built-in programmable dead time; external circuitry must be modified
AMC1311 NSI1311 Parameter coverage Supply is tight for some packages; note package differences indicated by part-number suffixes, and evaluate accuracy metrics at board level
AMC1301 NSI1300D25 Comparable parameters Item-by-item comparison of accuracy metrics with board-level verification; NSI1306 evaluated at a small ±50 mV range
ACPL‑790B NSI1300D25 Functional solution level Optocoupler architecture; pin-incompatible, board redesign required; avoids LED aging drift
TLP109 NSI72xx Pin-to-pin evaluation SOP-5 package; external resistor retuning required
ACPL‑M61L NSI72xx Pin-to-pin evaluation SOP-5 package; external circuit parameters require retuning
ISO1042 NSI1042 Parameter coverage Consistent package; reference design can be reused directly
ISO3082 NSI83085E/NSI83086E Parameter coverage 500 kbps half-duplex / 16 Mbps full-duplex; verify system rate
NOVOSENSE supplement NSIP984x‑DSWWR 1500 V extension Creepage distance 15 mm, meeting PV energy storage safety standards
NOVOSENSE supplement NSI6911F Certification threshold coverage China's first ASIL D isolated driver
附样品申请二维码

Sample request attached

微信公众号二维码

WeChat Official Account

← Back to Solutions