As automotive electronics rapidly evolve toward high integration, high reliability, and low cost, automotive-grade load driver ICs, as key devices in core scenarios such as body control, lighting systems, and powertrains, directly affect vehicle system design efficiency and operational stability through their performance and cost-effectiveness. Just yesterday, NOVOSENSE officially launched China's first automotive-grade 8-channel configurable high-/low-side driver series—NSD56080, NSD56602, NSD56620, and NSD56242 (collectively the 'NSD56xxx-Q1 series')—leveraging advantages such as high integration, flexible configuration, and intelligent diagnostics to inject strong momentum into the domestic substitution of automotive-grade driver ICs.

1. Domestic Breakthrough: Filling the Gap
The launch of NOVOSENSE's NSD56xxx-Q1 series successfully fills the domestic technical gap in automotive-grade 8-channel configurable high-/low-side driver ICs, marking an important breakthrough for domestic chips in this field.

The NSD56xxx-Q1 series operates over a voltage range of 4.5 V to 28 V (with an internal output clamp of 39 V) and provides 330 mA drive current per channel (all channels ON), making it suitable for driving various inductive and capacitive loads in automotive electronics, such as relays, LEDs, bulbs, and motors. Compared with the mass-produced 8-channel low-side driver NSD56008, the new products add core functions such as an automatic PWM generator, on-state open-load diagnostics, and Bulb Inrush Mode, helping customers save MCU resources, reduce system design complexity and cost, and shrink board size, further improving design flexibility and integration while fully benchmarking the DRV81xxx-Q1 series from international giant Texas Instruments (TI) (primarily represented by the DRV81242-Q1).
Parameter Comparison Table
| Part Number | DRV81242-Q1 (Texas Instruments, TI) | NSD56242-Q1 (Novosense) |
| Integrated channels | 4 high-side / 2 low-side / 2 configurable high-side/low-side | 4 high-side / 2 low-side / 2 configurable high-side/low-side |
| Supply voltage | 3 V to 40 V | 4.5 V to 28 V |
| Nominal load current | 330 mA (all channels operating simultaneously) | 330 mA (all channels operating simultaneously) |
| Core features | Two independent internal PWM generators; bulb inrush mode (BIM); limp home mode | Two independent internal PWM generators; BIM mode; limp home mode |
| Diagnostic features | Open-load detection in on/off states | ON-State and OFF-State dual-mode load open-circuit diagnostics |
| Protection Features | Integrated clamping circuit at the output | Integrated active clamp transistor per channel (for inductive loads) |
| Key Advantages | Wide operating voltage; years of leading experience and more mature technology, etc. | High integration and higher cost-effectiveness; optimized for incandescent lamp driving, etc. |
II. Core Functions: Benchmarking Against World-Leading Technology
1. Built-in PWM Auto Generator: Frees Up MCU Resources and Improves Response Efficiency
The NSD56xxx-Q1 series chips and TI's DRV81242-Q1 both integrate two independent PWM auto generators; the PWM frequency and duty cycle are configurable, and the generators can be mapped to any output port. Together with two inputs (which can also be mapped to any output port), they can output up to 4 independent PWM signals with different frequencies and duty cycles, directly saving two MCU PWM ports and software resources. This design greatly simplifies system control logic. For example, in scenarios such as automotive multi-zone LED lighting dimming and relay hierarchical control, precise driving can be achieved directly through internal chip configuration, reducing the MCU computational load and improving system response speed and stability.

Input Mapping
2. Limp Home Mode: Ensures Vehicle Safety Redundancy
When the vehicle system detects an abnormal fault, the NSD56xxx-Q1 series can quickly enter Limp Home mode. Through an 8-channel selective shutdown mechanism, only two mapped channels remain continuously operating. These two channels can prioritize power supply to critical safety loads such as relays, brake pumps, and power steering, ensuring that the vehicle can still maintain basic driving functions under fault conditions, giving the driver time for emergency handling and significantly improving the vehicle's safety redundancy level.
3. BIM Mode: Solves Multi-Load Driving Pain Points and Expands Application Scenarios
In automotive electronics, when high-side/low-side driver chips drive incandescent lamps or capacitive loads, the inrush current at startup often triggers over-load protection, causing the channel to shut down. Traditional solutions rely on software to repeatedly clear the fault and restart the channel; response is slow and it is difficult to provide sufficient energy for load startup, especially affecting the normal operation of loads such as incandescent lamps that require instantaneous high-power startup.
To solve this pain point, the NSD56xxx-Q1 series, like the DRV81242-Q1, integrates Bulb Inrush Mode (BIM). When the channel output reaches the over-load protection threshold and is shut down, the channel automatically restarts after tINRUSH and repeats continuously until the duration tBIM (40 ms). Within 40 ms, there is enough time to light a 2 W bulb; if BIM mode and channel paralleling are used simultaneously, it can support lighting a 5 W bulb.

Bulb Inrush Mode (BIM) Operation
This design enables the NSD56xxx-Q1 series to reliably drive capacitive and inductive loads such as incandescent lamps, relays, and motors, significantly improving system compatibility with different load types and providing customers with more flexible and reliable design options.
III. Innovative Design, Reliable Assurance
1. Intelligent Diagnostics: Dual-Mode Open-Load Detection Simplifies System Design
Compared with the already mass-produced predecessor NSD56008, which provides load diagnostics through open-load and short-circuit detection in the off state, the newly released NSD56xxx-Q1 series devices add support for dual-mode load open-circuit diagnostics (OLD) in both OFF-State and ON-State, achieving the same diagnostic level as the DRV81242-Q1. They support accurate detection of load connection status when the output is off or on, significantly enhancing the system's self-diagnostic capability.
- OFF-State OLD (off-state diagnostics): By enabling the built-in diagnostic current source for each channel and comparing the output port voltage, it determines whether the load is open. This is suitable for the basic diagnostic needs of most loads.
- On-State OLD (on-state diagnostics): Applicable only to high-side channels and channels configured as high-side. It performs accurate diagnostics by detecting the actual load current and output port voltage. This mode solves the industry pain point in OFF-State diagnostics where the internal current source causes LED loads to glow faintly. It also supports selected single-channel diagnostics or cyclic diagnostics across all high-side channels. Only one message frame is needed to read diagnostic information for all channels, greatly simplifying system design and reducing MCU load.
In automotive lighting systems, sensor connection detection, and other scenarios, dual-mode diagnostics enable real-time monitoring of load status, timely feedback of open-circuit faults, facilitate rapid problem localization, and improve overall vehicle maintenance efficiency.
2. Integrated Active Clamp Transistor: Easily Handles Inductive Loads and Reduces System Cost
When driving inductive loads such as relays and solenoids, a high-voltage spike is generated at the moment the channel is turned off due to the release of inductive energy. If the energy is too large, it can easily cause avalanche breakdown of the power transistor inside the chip. The TI DRV81242-Q1 mitigates this issue with an integrated clamp circuit at the output, while the NOVOSENSE NSD56xxx-Q1 series adopts a more targeted design with an integrated active clamp transistor (Active Clamp) per channel.
When a channel is turned off, the active clamp transistor quickly clamps the output voltage (the low-side channel clamps a positive voltage, and the high-side channel clamps a negative voltage). At the same time, the output power transistor is turned on because its gate voltage is raised, forming a current path that discharges the inductive energy and effectively prevents damage to the power transistor. This hardware-level protection mechanism requires no additional external clamp transistors (reducing external components by up to 8), which not only lowers BOM cost but also reduces board-level footprint.
A single channel of the chip can withstand clamp energy of up to 50 mJ at room temperature, while the turn-off energy generated by commonly used automotive relay loads is usually less than 10 mJ. This fully covers typical application requirements and ensures stable and reliable operation of the chip during long-term, high-frequency switching.

Output Power Transistor Active Clamp
IV. Automotive-Grade Quality, Stable Supply, and Flexible Selection
Also as an automotive electronic product, the NSD56xxx-Q1 series of 8-channel intelligent high-side/low-side driver products meets the AEC-Q100 Grade 1 standard, with an operating temperature range of -40°C to 125°C and an HTSOP24 package (8.65×3.9 mm). With automotive-grade reliability, comprehensive high-side/low-side combinations, and rich intelligent functions, NOVOSENSE can provide multi-channel, highly integrated solutions for driving various types of body electronics loads. The entire series is already in mass production, helping customers quickly build safe, reliable, flexible, and efficient system designs.

NDS56xxx-Q1 Selection Guide

DRV81xxx-Q1 Series Devices
V. Conclusion
The launch of the NOVOSENSE NSD56xxx-Q1 series fills the gap in domestic automotive-grade 8-channel configurable high-side/low-side driver chips. Its core competitiveness centers on 'high integration + high cost-effectiveness + precise scenario adaptation':
- Compared with TI's DRV81242-Q1, the NSD56xxx-Q1 significantly reduces system BOM cost and board-level footprint through designs such as integrated active clamp transistors and streamlined redundant voltage adaptation, while ensuring consistent core functions. It is more suitable for cost-sensitive economy and mid-range vehicle models;
- Compared with traditional discrete driver solutions, this series integrates multi-channel driving, diagnostics, and protection functions into a single device, reducing the number of external components, improving system reliability, and shortening customers' development cycles.
Against the backdrop of accelerating localization of China's automotive supply chain, compared with the DRV81242-Q1's 'hard-to-obtain' status (supply chain volatility + high price), the NSD56xxx-Q1 series is a cost-effective integrated solution. Its built-in advanced functions help users effectively control cost and size while ensuring performance, making it a preferred option for domestic automakers to replace imported chips and helping users build a localized architecture system.
For more information about the NSD56xxx-Q1 series or to request samples, please contact the official authorized distributor: Email: sales@chiplinkstech.com; WeChat Official Account: Zhilian Micro - Motor Control Chips, which provides part selection services and technical support. We look forward to working with you.

Sample Request

WeChat Official Account