0755-82557621 sales@chiplinkstech.com Mon–Fri 09:00–18:00 (UTC+8)
Precision motion control · Components and solutions

NOVOSENSE's New NSD7309 Brushed DC Motor Driver: 10 A Output Fills High-Current Gap for Compact Devices

As industrial automation, smart home appliances, and portable devices continue to evolve toward high power density and compact designs, motor control systems face the conflict between limited PCB area and high-current drive capability, as well as the dual requirements of battery-powered systems for low-voltage operation and low standby power consumption. This is driving brushed DC motor control chips toward higher current, lower impedance, and smaller footprint [...]

2026-06-26 New Product Information
纳芯微新品NSD7309直流有刷驱动:10A输出,填补紧凑型设备大电流空白

As industrial automation, smart home appliances, and portable devices continue to evolve toward high power density and compact designs, motor control systems face the conflict between limited PCB area and high-current drive capability, as well as the dual requirements of battery-powered systems for low-voltage operation and low standby power consumption, driving brushed DC motor control chips toward higher current, lower impedance, and smaller footprint.

At PCIM Europe 2026, NOVOSENSE Microelectronics showcased the new NSD7309 brushed DC motor driver; the brushed DC drivers exhibited alongside it also included the NSD7305 and NSD7308. The three new products cover a peak current range of 10 A to 21 A, filling NOVOSENSE's market gap in the medium- and high-power commercial and industrial brushed DC drive segment. Together with the existing NSD731x series (3.6 A class, 6 A class) and NSD7315 series (10 A automotive-grade), they form a 40 V-class brushed DC driver product matrix ranging from light load to heavy load and from commercial to automotive-grade.

1. Complementing the Portfolio to Fill a Market Gap

The NSD7309 is a precise addition to NOVOSENSE's own product portfolio in response to the tiered demand in the brushed DC drive market. Before this, NOVOSENSE's brushed DC driver product line had already formed two mature series, but there was still a gap in medium- and high-power commercial and compact high-current scenarios:

NSD731X series (NSD7310/NSD7312): centered on 3.6 A-class products (NSD7314, 6 A peak), it uses an HSOP8 package, an external sense resistor, and pure hardware control, offering low cost and a simple design for light-load scenarios such as robot vacuums, home appliances, and electronic locking for NEV charging connectors. Limited by its architecture, its peak current ceiling is relatively low, making it difficult to meet the needs of higher-power motors.

NSD7315 high-end series: positioned as a 10 A-class high-performance solution, it uses an HTSSOP24 package and comes standard with built-in current sensing, SPI register configuration, and comprehensive fault diagnostics, targeting high-end industrial and automotive-grade scenarios. The chip cost is higher and the package size is larger, making it unsuitable for compact, budget-constrained designs.

The new NSD7309, NSD7308, and NSD7305 unveiled at PCIM Europe 2026 round out the commercial and industrial power range from 10 A to 21 A.

Model Peak Current On-Resistance Supply Voltage Interface Positioning
NSD7310/7312 3.6A 520mΩ 5~36V Hardware Light-Load General Purpose
NSD7309 10A 120mΩ 5~40V Hardware Medium-Power Commercial
NSD7315 10A 150mΩ 4.5~35V Hardware + SPI Medium-Power Automotive-Grade
NSD7308 12A 84mΩ 40V Hardware + SPI Mid-to-High-End Industrial
NSD7305 21A 47mΩ 40V Hardware + SPI High-Current Flagship

Among the three new products, the NSD7309 plays a dual role: "power upgrade in a small package" and "cost reduction for the high-current tier." In terms of packaging, it raises the peak current capability of the HSOP8 package from the original 3.5 A to 10 A, enabling compact designs to drive higher-power motors. In the 10 A current class, it offers a cost-effective option with external current sensing and pure hardware control, differentiating it from the high-end NSD7315 solution with built-in sensing + SPI. This allows customers who do not need complex diagnostics and register configuration to obtain high-current drive capability at lower cost.

 

II. NSD7309 in Detail: Balancing Reliability and Ease of Use

The NSD7309 is a single-channel H-bridge DC brushed motor driver IC with four integrated N-channel MOSFETs. It uses a current chopping architecture with an external sense resistor and pure hardware control logic via IN1/IN2. It is suitable for compact motor control applications and has a low hardware development barrier.

Functional Block Diagram

1. Wide Voltage, High Current

The chip supports an operating voltage range of 5 V to 40 V, with an absolute maximum rating of 45 V. Its 5 V lower supply limit can connect to a 3-cell lithium battery (about 9 V) or 2-cell lithium battery (about 6 V) power system; the 40 V upper limit covers mainstream 12 V and 24 V industrial and home appliance power systems, allowing it to handle complex conditions such as power surges and load transients with ease.

In terms of output capability, the peak output current is 10 A, and the typical full-bridge on-resistance is 120 mΩ (60 mΩ high side + 60 mΩ low side), covering high-current inrush scenarios such as startup and stall of low-to-medium-power DC brushed motors.

2. Pure Hardware Pin Control

The NSD7309 uses IN1/IN2 two-pin hardware control logic, with a PWM frequency of up to 200 kHz. It requires no SPI register configuration or complex software development, and can implement four operating modes through combinations of logic levels:

  • Forward drive: IN1 high, IN2 low;
  • Reverse drive: IN1 low, IN2 high;
  • Slow-decay braking: IN1 and IN2 are both set high, and both outputs are pulled low simultaneously;
  • Fast-decay coasting: IN1 and IN2 are both set low, and both outputs enter a high-impedance state.

IN1 and IN2 have built-in pull-down resistors and default to low level when floating, preventing erroneous operation at power-up. When IN1 and IN2 are both held low for more than 1 ms (typical), the chip automatically switches from fast-decay mode to low-power sleep mode, turning off the internal charge pump and core control logic. The sleep current does not exceed 7 μA, reducing system standby power consumption.

3. Precise Current Chopping

NSD7309 integrates fixed off-time current chopping regulation: the motor current is converted into a voltage signal through an external sense resistor connected to the ISEN pin; after amplification by an internal 10 V/V gain amplifier, it is compared with the reference voltage at the VREF pin (0.3 V to 3.6 V). When the current exceeds the set threshold, the H-bridge enters slow decay for 30 μs and then automatically resumes driving; a built-in 1.5 μs blanking time masks voltage spikes during switching to prevent false current-limit triggering. Current threshold calculation formula: ITRIP=VREF/(AVISEN×RISEN). This current-limiting mechanism can effectively limit startup and stall peak currents, reducing thermal stress and supply stress.

4. Comprehensive Protection System

NSD7309 integrates a three-level fault protection mechanism. After all faults are cleared, it can automatically resume normal operation without a host reset:

  • VM undervoltage lockout (UVLO): the output is turned off when the supply voltage is below 3.7 V, and automatically recovers when it rises above 3.9 V; hysteresis is 200 mV;
  • Overcurrent protection (OCP): shutdown is triggered when the H-bridge output current exceeds 13 A for more than 1.5 μs, and recovery is automatically attempted after 5 ms;
  • Thermal shutdown (TSD): the H-bridge is turned off when the junction temperature reaches the 155°C to 185°C range, and automatically recovers after the temperature falls to approximately 120°C to 155°C; hysteresis is approximately 30°C.

Additionally, the chip offers two model options: NSD7309 (Pin 4 is the VREF reference voltage input) and NSD7309N (Pin 4 is the nFAULT open-drain fault output), allowing customers to choose flexibly based on system diagnostic requirements.

5. ESD Protection and Package Thermal Dissipation

Power pins (VM, OUT1, OUT2, GND, ISEN) have an HBM protection rating of ±4 kV; logic pins (IN1, IN2, VREF/nFAULT) have HBM ±2 kV; all pins have CDM ±750 V.

The package is an HSOP8 package with an exposed thermal pad (4.90 mm × 3.90 mm). The chip supports an operating junction temperature range of -40°C to 150°C. With proper PCB thermal design, it can operate in high-temperature environments and enclosed equipment.

Pin Package View (right, NSD7309N)

III. Benchmarking Against Competitors: Performance Differences in the Same Package

Market competitors AT8236 and SA8882 in the same package were selected for a side-by-side comparison.

Parameter NSD7309 AT8236 SA8882
Operating Voltage 5V~40V 5.5V~36V 6V~45V
Peak Current 10A 6A 8A
On-Resistance 120mΩ 200mΩ 95mΩ
Maximum PWM Frequency 200kHz 100kHz 200kHz
Sleep Current ≤7μA 20μA(typ) 3μA(typ)
OCP Threshold 13A 7A(typ) 9.5A
UVLO Rising Threshold 3.9V 4.7V 5.8V
Package HSOP8 ESOP8 ESOP8

From the comparison, several competitive characteristics of the NSD7309 in the market can be seen:

  • Wide voltage range: The NSD7309 has a wide operating voltage of 5 V to 40 V. The 5 V lower limit is compatible with low-voltage lithium battery systems, while the 40 V upper limit covers 24 V industrial power platforms—both with margin. The 3.9 V UVLO threshold helps low-voltage battery-powered systems maintain longer effective operating time as voltage drops. All parameters are clearly specified.
  • Current capability in the same package: In an 8-pin package, the NSD7309's 10 A peak current is advantageous, enabling it to drive higher-power motor loads without increasing PCB footprint. In addition, the NSD7309 package is smaller (4.90 mm × 3.90 mm, versus approximately 5.00 mm × 6.20 mm for the AT8236).
  • High-frequency PWM and low power consumption: The NSD7309's 200 kHz PWM upper limit is advantageous in scenarios requiring ultrasonic-band quiet drive. For sleep power consumption, the NSD7309's 7 μA is better than the AT8236's 20 μA and slightly higher than the SA8882's 3 μA; all three are low-power products.
  • Protection functions: The NSD7309's protection thresholds have wider design margins than most comparable competitors on the market, enabling better adaptation to complex operating conditions.

 

IV. Application Scenarios

Based on its wide-voltage and high-current characteristics, the NSD7309 is suitable for a variety of DC brushed motor drive scenarios:

  • Office automation equipment: motor drive for the paper feed and cutting mechanisms of printers, scanners, and label printers.
  • Smart home and small appliances: motor drive for products such as electric curtains, robot vacuums, massage chairs, height-adjustable desks, and small kitchen appliances.
  • Industrial control equipment: drives for small conveyors, industrial pumps and valves, pneumatic actuators, security PTZ units, and other equipment.
  • Battery-powered equipment: small robots and portable industrial devices powered by multi-cell lithium batteries.

 

V. Conclusion

The launch of the NSD7309 marks an important step for NOVOSENSE's DC brushed motor driver product line from 'current-tier coverage' to a 'refined portfolio layout.' It precisely addresses a market pain point—filling the market gap for high-current drivers in HSOP8 packages and adding a cost-effective, hardware-only option in the high-current tier to complement high-end solutions.

With the full rollout of the NSD7305, NSD7308, and NSD7309, NOVOSENSE's product portfolio in the 40V medium- and low-voltage DC brushed driver field will become more complete, covering everything from entry-level low-cost to high-end high-performance and from low power to high power, providing customers with more flexible, better-fitting domestic driver chip options.

For more information about the NSD7309 or to request samples, please contact: sales@chiplinkstech.com; 18820174321, Mr. Xu.

附样品申请二维码

Sample Request Attached

微信公众号二维码

WeChat Official Account

← Back to News