The TMC2660C is a highly integrated, intelligent two-phase stepper motor driver IC launched by Trinamic. With the core advantages of “precision control + low power consumption + silent operation,” it integrates power MOSFETs, advanced current control algorithms, and sensorless diagnostic functions. It can realize stepper motor driving in mid-to-high-end scenarios without requiring a large number of external components. It can be widely used in industrial automation, medical equipment, office equipment, and other fields sensitive to precision and noise, perfectly solving pain points of traditional stepper motor drive solutions such as noise and vibration, low efficiency and heat generation, and step loss faults.

1. Core Engine: Highly Integrated Power Architecture
1. Product Introduction
The TMC2660C is a highly integrated two-phase stepper motor driver IC and a C-type upgrade of the previous-generation TMC2660. Following the design philosophy of “using chip-level intelligence to solve system-level challenges,” it packages high-power MOSFETs, advanced control logic, and intelligent diagnostic algorithms into a 44-pin QFP chip. It supports a wide motor supply voltage from 5 V to 30 V and can provide up to 2.2 A RMS continuous phase current, sufficient to drive most small and medium-sized stepper motors.
Core Feature Parameter Table
| Drive Capability | Continuous 2.2 A RMS, peak 2.8 A RMS |
| Supply voltage | 5–30 V DC, absolute maximum voltage 0.5–60 V |
| Maximum resolution | Supports 256 microsteps per full step |
| Package | QFP-44(10mm×10mm) |
| Operating temperature | -40~125℃ |
| Control interface | SPI; STEP/DIR; Standalone Mode |
| Protection and Diagnostics | Overcurrent, short-to-ground, overtemperature, and undervoltage protection |
| Core Technology | SpreadCycle™;MicroPlyer™;
StallGuard2™;CoolStep™ |

Pinout and Package Diagram
2. Key Architecture Advantages
- Fully Integrated Power Bridge: The chip integrates two independent N-channel power MOSFET full bridges internally, which can directly drive two-phase stepper motor windings. Its low on-resistance design ensures extremely high power conversion efficiency and significantly reduces thermal losses during operation, laying a solid foundation for long-duration, high-load continuous industrial operation.
- Lossless Current Sensing: Innovative integrated power sensing technology eliminates the need for external shunt resistors, enabling real-time, high-precision sampling of motor phase current, saving PCB space and external component costs, and further eliminating accuracy errors caused by temperature drift of external resistors.
- Wide power supply adaptability: A wide operating voltage range of 5V to 30V, enabling flexible adaptation to various industrial standard DC bus voltages without additional voltage conversion modules.
- Enhanced design: Based on the previous-generation TMC2660, the TMC2660C optimizes chopper operation to reduce noise during low-speed motor operation and performs undervoltage monitoring on VCC_IO to ensure stable power-up and power-down processes, while reducing internal circuit power consumption and heat generation.

Simplified block diagram
II. Intelligent Core: Specialized Technology Analysis
With multiple proprietary core technologies, the TMC2660C achieves breakthroughs in four dimensions: quietness, smoothness, energy efficiency, and reliability. The specific technical features and advantages are as follows:
SpreadCycle™Anti-jitter technology:High-precision chopper algorithm: By optimizing the motor control algorithm and drive strategy, it reduces vibration and noise during high-speed motor operation, effectively suppresses jitter and resonance, and enables the stepper motor to maintain smooth and stable operation at high speed. This technology improves system operating stability and precision and reduces noise pollution.
MicroPlyer™Microstep interpolator:When low-resolution pulses (such as 16 microsteps) are input through the STEP/DIR interface, the chip automatically interpolates them internally to 256 microsteps and generates smooth current waveforms through an optimized sine wave lookup table (1024 entries), allowing motion precision to be upgraded without replacing the external controller. It improves the precision of new equipment while remaining compatible with retrofits of legacy equipment, reducing system upgrade costs, and is especially suitable for factory automation scenarios where 'existing PLCs are retained while motor control precision is improved'.
CoolStep™Adaptive current control:This technology uses the load value provided by StallGuard to dynamically adjust the motor current supply. When the load is low, CoolStep™ reduces the motor current supply, thereby reducing motor heating and energy consumption; when the load increases, the current supply automatically increases to ensure normal motor operation. This technology can save up to 75% energy, effectively reducing equipment power consumption and heating, and is suitable for long-term operation or battery-powered devices.
StallGuard2™Sensorless stall detection:This technology enables stepper motors to perform stall detection without additional sensors. By monitoring changes in motor current and voltage, StallGuard™ can infer the load level, providing a basis for subsequent control strategies. It simplifies system structure and reduces cost while improving system reliability and flexibility. Its measurement value varies linearly over a wide range of load, speed, and current, and the heavier the load, the closer the value is to zero.
III. Comprehensive Diagnostic and Protection System
In harsh industrial environments, reliability is a lifeline. The TMC2660C incorporates a multi-level, comprehensive hardware protection and diagnostic mechanism to safeguard system safety.
1. Real-time fault monitoring and diagnostic information output:It continuously monitors the chip junction temperature, supply voltage, and output circuit status. All fault statuses and operating data (load value, temperature, fault type) can be read in real time via the SPI interface, providing data support for predictive maintenance and remote fault diagnosis. In addition, the TMC2660C optimizes the filtering time of the STEP/DIR inputs to reduce the risk of step loss.
2. Active protection mechanisms:
- Overcurrent protection (OCP): Prevents current surges caused by motor stall or short circuit.
- Short-circuit protection (SC): Shuts down immediately when an output is shorted to ground or the power supply, with newly added low-side short-circuit protection.
- Overtemperature protection (OTSD): Automatically enters shutdown when the junction temperature exceeds the safety threshold (selectable 136°C/150°C).
- Undervoltage lockout (UVLO): Ensures the driver does not operate when the supply voltage is insufficient, avoiding abnormal states. The TMC2660C can lower the undervoltage threshold from 7 V to 4.5 V via the EN_PFD bit.
- Clock failure protection: After the TMC2660C enables the EN_S2VS bit, if the external clock fails, it can automatically switch to the internal clock to prevent damage to the motor and driver.
IV. Application Scenarios
With its high integration (integrated MOSFETs), intelligence (sensorless detection and energy saving), and quiet operation, the TMC2660C is ideal for precision equipment with strict requirements for space, energy efficiency, and noise.
Office automation: high-end printers, scanners, automatic paper feeders, etc. Quiet operation improves the office environment, while low power consumption reduces overall system energy consumption.
Industrial and automation: small CNC machine tools, textile and sewing machines, robot joints, and liquid handling pumps and valves. Energy-saving features and high reliability meet the demands of continuous operation.
Precision instruments: medical equipment, laboratory automation equipment, and optical instruments, where both quietness and precision are indispensable.
Security and finance: surveillance PTZ cameras (CCTV) and banknote transport mechanisms in automated teller machines (ATMs). Intelligent anti-stall protection ensures stable core functions.
Consumer innovation: precision drive in high-performance 3D printers and smart home devices. Microstep accuracy and quiet operation directly enhance product competitiveness.
V. Simplified Development: Accelerating Innovation into Deployment
To enable engineers to quickly unlock the powerful potential of the TMC2660C, Trinamic provides complete ecosystem support:
- Standard interfaces: Equipped with an SPI interface for parameter configuration and diagnostics, and compatible with the traditional STEP/DIR interface, enabling seamless adaptation to both new and legacy control systems. The SPI interface supports a maximum clock frequency of 8 MHz (with an external 16 MHz clock).
- Evaluation kit: The TMC2660-EVAL evaluation board includes all necessary hardware and interfaces and provides a comprehensive functional verification platform. Users can power it up and drive a motor in a short time, allowing them to directly experience all advanced features.
- Software tools and technical support: With dedicated configuration software and detailed API libraries, even complex motion profiles and sensorless algorithms can be quickly integrated into the user's control system.
- Ready-to-use modules: Such as the TMC2660-BOB breakout board and Mikroe's SilentStep 3 Click module, enabling 'plug-and-play' rapid prototyping and minimizing time to market.
- Convenient configuration in standalone mode: In standalone mode, microstep resolution, chopper hysteresis, and motor current can be configured via 3 pins, without SPI communication, simplifying the development process.
VI. Conclusion
The TMC2660C is a highly integrated, cost-effective bipolar stepper motor driver IC that combines powerful driving capability, fine sensing capability, extremely low power consumption, and meticulous protection in one. It is suitable for precision scenarios such as industrial automation, medical, and office applications. As a C-type upgraded version, it optimizes quiet operation and adds features such as low-side short-circuit protection, significantly improving reliability and adaptability.
In today's pursuit of ultimate efficiency, precision, and reliability, when a product needs a 'powerful and smart' heart to drive precise motion, the TMC2660C can be a key partner for product differentiation and market success. For more information about the TMC2660C or to request samples, please contact: sales@chiplinkstech.com (email); WeChat Official Account: Chiplink-Motor Control Chips. We look forward to working with you.

Sample request attached

WeChat Official Account