I. Product Overview
SS8870T is a domestically produced brushed DC motor driver IC that uses a single-channel H-bridge topology and can drive one DC motor, one winding of a stepper motor, or other loads.The chip integrates four N-channel MOSFETs and supports6.5V~40V(1.0 datasheet; adjusted in version 1.2: 8.5V~40V) wide voltage input, peak output current3.6A. Two logic inputs control the H-bridge output, supporting four operating modes: forward, reverse, brake, and coast. Speed can be controlled by PWM, with a frequencyof up to 100 kHz. Suitable for mechatronic applications such as printers, home appliances, and industrial equipment.

II. Key Parameters and Features
The SS8870T uses a full N-channel MOSFET architecture, with an on-resistance of520mΩ(HS+LS), 260 mΩ each for high side and low side (typical), lower than the comparable competing DRV8870 (565 mΩ) on the market, resulting in less heat generation during high-current continuous operation and advantages for thermal design and efficiency.
The chipintegrates a current regulation function. By inputting a 0.3–5 V reference voltage to the VREF pin and using an external current-sensing resistor connected to the ISEN pin, the motor current can be limited to a preset value. The calculation formula is: I_TRIP=VREF/(10×R_ISEN). When the winding current reaches the current-limit threshold, the chip automatically enters slow decay mode, with a fixed off-time of 30 μs; it also has a built-in 3.2 μs blanking time to mask current spikes at switching instants and avoid false triggering of the current limit. This function can clamp the current at a known level during motor startup and stall, reducing reliance on large-capacity capacitors and lowering BOM cost. When current regulation is not used, simply connect ISEN to ground.
SS8870TBuilt-in charge pump drives the high-side MOSFET, no external bootstrap circuit is required; the single supply VM powers both the chip and the motor, simplifying the peripheral design.
The chip also featureslow-power sleep mode: after IN1 and IN2 are pulled low simultaneously for 1.2 ms, it enters sleep mode with a quiescent current of 15 µA. The wake-up time from sleep is 45 µs, which is friendly for the standby battery life of battery-powered devices.
III. Hardware Protection and Package
In terms of protection mechanisms, the SS8870T integrates triple hardware protection. Except for overcurrent protection, which uses an automatic retry strategy, the others support fault self-recovery and require no additional reset circuit, improving long-term system reliability:
- Undervoltage lockout (UVLO):Triggered when the VM supply drops to 8 V (typical), turning off all power transistors; it automatically recovers after the voltage rises to 6.0 V, preventing abnormal device operation at low voltage.
- Overcurrent Protection (OCP):Triggers when the output current exceeds 2 A (typical), with a built-in 2.5 μs deglitch time to reject transient spike interference; after triggering, it turns off the H-bridge and automatically retries at 4 ms intervals. Once the fault is cleared, it automatically resumes normal operation without external intervention.
- Thermal Shutdown (TSD):Triggers when the chip junction temperature reaches 170°C (typical), turning off all outputs; it has 40°C hysteresis and automatically recovers after the temperature falls 40°C below the threshold, preventing overheating damage to the device.
In terms of packaging, the chip usesESOP-8 package, with an exposed thermal pad on the bottom, balancing small size and heat dissipation capability, and suitable for space-constrained compact designs. The operating junction temperature range is -40°C to 125°C, withstanding high-temperature scenarios.

Pinout Package View
IV. Competitive Product Comparison
Two comparable international products on the market are selected for comparison:
| Parameter | SS8870T | TI DRV8870 | Toshiba TB67H450AFNG |
| Operating Voltage | 6.5V~40V | 6.5V~45V | 4.5V~44V |
| Peak Output Current | 3.6A | 3.6A | 3.5A |
| RDS(ON)(HS+LS) | 520mΩ | 565mΩ | 600mΩ |
| Integrated Current Regulation | Yes (VREF+ISEN) | Yes (VREF+ISEN) | Yes (VREF+RS) |
| Sleep/Standby Current | 15µA | 10µA | 1µA |
| UVLO | Yes | Yes | Yes |
| OCP | Yes (4.2A, automatic retry) | Yes (automatic recovery) | Yes (fault latch) |
| TSD | 170°C | 175°C | 160℃ |
| Package | ESOP8 | HSOP-8 | HSOP8 |
The SS8870T is positioned close to the DRV8870 and TB67H450AFNG, is pin-compatible, and can replace them in most scenarios.
V. Conclusion
The SS8870T is a China-made single-channel H-bridge brushed DC motor driver that supports a 6.5V–40V supply, has a 3.6A peak current and 520mΩ on-resistance, and integrates current regulation and UVLO, OCP, and TSD protection. Its pins are compatible with the DRV8870 and TB67H450AFNG, so it can serve as an alternative. At the same time, under the trend of domestic substitution, this chip has clear advantages in supply stability, cost control, and local technical support, making it suitable for printers, home appliances, industrial equipment, smart home products, and other mechatronic products with comprehensive requirements for space, efficiency, and reliability.
For more product information or to request samples, please contact: sales@chiplinkstech.com; Engineer Chen, 13924675549.

Sample Request Attached

WeChat Official Account