0755-82557621 sales@chiplinkstech.com Mon–Fri 09:00–18:00 (UTC+8)
Precision motion control · Components and solutions

NSUC1612E: Fully Integrated SoC Solution for Low-Power Motor Control

As automotive E/E architectures evolve toward integration, low-power motor applications in the body—such as HVAC air dampers, electronic water valves, active grille shutters, and charging port covers—place higher demands on actuator miniaturization, lightweighting, and reliability. NOVOSENSE’s NSUC1612E is an automotive-grade motor driver SoC designed to meet these needs; it integrates processing [...]

2026-05-07 Solution Applications
NSUC1612E:面向小功率电机控制的全集成SoC方案

As automotive E/E architectures evolve toward integration, low-power motor applications in the body, such as HVAC air dampers, electronic water valves, active grille shutters, and charging port covers, place higher demands on actuator miniaturization, lightweighting, and reliability. The NSUC1612E launched by NOVOSENSE is an automotive-grade motor driver SoC that addresses these needs; it highly integrates processing, driving, and communication functions into a single chip, providing a compact and efficient solution for distributed intelligent actuators.

1. “All-in-One” Design

The core appeal of the NSUC1612E lies in its “All-in-One” design philosophy, which deeply integrates four functional domains into a single chip to build a complete electromechanical control unit:

  • High-performance processor: a 32-bit ARM Cortex-M3 core using the Harvard architecture, with independent data and address buses and a three-stage pipeline, achieving approximately 1.25 DMIPS/MHz processing performance and easily handling complex algorithms such as FOC;
  • 3-channel half-bridge driver: integrates 6 N-channel MOSFETs, with a 2.1 A peak drive current and 1.4 A RMS current, and can directly drive brushed DC, brushless, and stepper motors;
  • Rich communication interfaces: integrated LIN PHY, supporting LIN 2.x/ISO 17987/SAE-J12602 protocol standards; integrated FlexCAN controller, compatible with the CAN 2.0B bus specification, supplemented by SPI/SSI, enabling flexible integration into in-vehicle networks;
  • Precision analog peripherals: includes a 12-bit high-precision ADC, a PGA programmable gain amplifier, two 8-bit DACs, and a BEMF (back electromotive force) comparator, as well as dual temperature sensors, dual watchdogs, and other system protection modules, providing hardware support for precise motor control and safe operation.

System Block Diagram

With a highly integrated architecture, work that originally required several chips and dozens of external components can now be fully handled by a single NSUC1612E. This not only reduces a large number of external components and shrinks PCB area, but also fundamentally simplifies the system supply chain and manufacturing process, enabling cost reduction and efficiency improvement as well as miniaturization and lightweighting of actuators.

Motor Drive 3 half-bridge outputs, 2.1 A peak drive current
Processing Core 32-bit ARM Cortex-M3 core
Memory 32KB Flash, 2KB SRAM, 15KB ROM (including BootLoader)
Communication Interfaces LIN2.x,FlexCAN,SPI/SSI
Analog Peripherals 12-bit high-precision ADC, two 8-bit DAC channels, and a comparator, with built-in BEMFC
Protection Features Overvoltage/overcurrent/overtemperature protection, ±40V LIN port withstand voltage
Automotive-Grade Certification AEC-Q100  Grade1
Operating Temperature -40°C to 125°C (maximum junction temperature 150°C)
Package Type QFN32 (5×5 mm) or HTSSOP24

QFN32 Pin Package View

II. Precise Drive and Sensitive Sensing

The core of motor control lies in precise current control and position feedback. The NSUC1612E is particularly solid in its design in these two areas.

On the drive side, the chip's half-bridge driver module uses a low on-resistance MOSFET design—low-side on-resistance (Rdson) 0.6 Ω, high-side 0.8 Ω—and can still maintain low heat generation under high-current drive. The internally integrated charge pump ensures that the high-side MOSFET can achieve 100% duty cycle output, which is extremely valuable in application scenarios requiring continuous full-power output, such as fully open valves and motor locking. More importantly, the MOUT module integrates overcurrent protection monitoring directly into the EPWM module, achieving cycle-by-cycle current protection at the hardware level, with response speed far exceeding software polling solutions.

On the sensing side, the NSUC1612E integrates a key component—a PGA programmable gain amplifier with a default fixed gain of 20×, dedicated to amplifying the weak voltage signal across the sampling resistor. The PGA output is brought out through the PGAO pin for ADC acquisition, providing a complete analog front-end solution for single-shunt FOC current sampling without the need to build an additional op-amp circuit. Paired with it, the BEMF back-EMF comparator supports six-step commutation control of sensorless BLDC motors and, with a 4-level adjustable hysteresis voltage (0/5/10/15 mV), allows engineers to dynamically balance motor startup reliability and signal noise immunity according to actual operating conditions, adapting to motor control requirements with different load characteristics.

III. Automotive-Grade Reliability

As a device for core automotive applications, stability and reliability are standard. The NSUC1612E has passed the stringent AEC-Q100 Grade 1 automotive-grade reliability certification and can operate stably over an ambient temperature range of -40°C to 125°C (maximum junction temperature up to 150°C). Whether during cold starts in extreme winter conditions or under continuous high-temperature operation in the engine bay, it maintains stable performance. For electrical protection, the LIN pin has a high withstand voltage of ±40 V, and the BVDD supply pin supports a wide withstand voltage range of -0.3 V to 40 V, allowing direct connection to a 12 V automotive battery and robust handling of extreme supply fluctuations such as load dump and cold crank.

At the same time, the chip integrates systematic hardware protection and diagnostic functions: the half-bridge driver supports cycle-by-cycle overcurrent shutdown; the power domain provides real-time overvoltage/undervoltage monitoring; hardware thermal shutdown is triggered when the junction temperature exceeds 165°C; and overcurrent, overvoltage, and overtemperature protection are all included. Independent window watchdog and digital watchdog can directly generate a system reset when software anomalies occur. Together with mechanisms such as dual temperature sensors and power transistor gate diagnostics, these provide underlying hardware support for system functional safety design. Combined with EMC performance compliant with CISPR 25 Class 5, NOVOSENSE builds the sense of “high reliability” in automotive electronics into every chip, enabling products to handle complex automotive environments with ease.

In terms of data storage, the chip’s integrated 32 KB Flash and 2 KB EEPROM support 100K erase/write cycles, with data retention of 10 years at 125°C junction temperature. Both Flash and EEPROM have built-in ECC, automatically correcting single-bit errors. More notably, the chip reserves 512 bytes of NVR memory, highly matching OEM requirements for frequent writes of key parameters.

IV. Fine-Grained Power Management

Today, as new energy vehicles and smart vehicles increasingly focus on vehicle energy consumption, quiescent current directly affects vehicle driving range and battery life. The NSUC1612E features a fine-grained multi-level power management design for automotive scenarios, strictly controlling standby power consumption while also ensuring fast response to bus wake-up. In active mode, chip power consumption is 10 to 15 mA; in sleep mode, consumption is below 50 µA across the full temperature range. This benefits from independent supply and wake-up logic for the LIN port and wake-up pin, meeting strict vehicle quiescent current limits while ensuring fast response.

The NSUC1612E also features Retention mode: when the supply voltage drops but does not trigger a power-on reset, the 1.5 V digital domain continues to power the SRAM, and after voltage recovery the CPU can quickly resume operation and record status. This feature provides critical support for system continuity under complex transient waveforms such as ISO 7637.

V. Product Synergy and Broad Scenario Coverage

The NSUC1612E is suitable for a variety of automotive low-power motor actuation scenarios that are sensitive to size, cost, and reliability:

  • Automotive thermal management systems: electronic water valves, HVAC damper actuators, HVAC valve control, etc.;
  • Cabin comfort systems: seat ventilation, automatic air outlet adjustment;
  • Intelligent body actuators: active grille shutter (AGS), charging port cover, hidden door handles, etc.

This highly integrated single-chip solution ensures performance while enabling simpler, more compact hardware designs and reducing customers' R&D and mass-production costs. To meet differentiated driving requirements across various segmented scenarios, NOVOSENSE also offers a product in the same series—the NSUC1612B: it integrates four half-bridge outputs with a peak current of 500 mA per channel, making it suitable for multi-channel low-current driving scenarios such as multi-channel ambient lighting drive or small stepper motor control. Together with the NSUC1612E, it forms a product matrix that covers a broader range of driving requirements for automotive distributed actuators.

VI. Conclusion

The in-depth development of automotive intelligence relies on the refinement and reliability upgrades of underlying actuators. The NSUC1612E highly integrated automotive-grade motor driver SoC precisely targets the miniaturization and integration needs of automotive distributed actuators, integrating processing, driving, and communication functions into a single chip. It is suitable for various automotive low-power motor control scenarios, helping automotive electronic systems continue to evolve toward greater integration, intelligence, and reliability.For more information about the NSUC1612E or to request samples, please contact the official authorized distributor: sales@chiplinkstech.com; phone: Engineer Chen, 13924675549 (same number on WeChat); WeChat official account: Zhilianwei - Motor Control Chips, providing product selection services and technical support.

附样品申请二维码

Request a Sample

微信公众号二维码

WeChat Official Account

← Back to Solutions