In modern industrial automation and intelligent transportation systems, the accuracy of angle and position detection directly affects the performance and reliability of the entire system. Traditional detection solutions often face challenges such as complex installation, susceptibility to interference, and limited accuracy. The MT6620 is a new-generation sensor IC launched by MagnTek (now part of NOVOSENSE) and developed based on fixed-pole Hall magnetic sensing technology for off-axis angle and position detection, providing an excellent solution for angle and position detection.

1. How It Works: Highly Integrated System Architecture
The MT6620 is a position and angle sensor IC based on Hall-array magnetic sensing technology and advanced signal processing technology. Its workflow is as follows:
- When a magnetic scale or magnetic ring with a corresponding pole pitch of 2 mm (must be compatible with radial magnetization specifications of 2 mm fixed pole pitch and 4 mm fixed pole pair) passes over the fixed 2 mm pole pitch Hall sensing array integrated in the chip, the Hall array outputs two sine/cosine analog voltage signals as the magnetic scale moves or the magnetic ring rotates;
- After amplification and filtering by the analog front-end circuit, the signals enter an ADC (analog-to-digital converter) for digital quantization;
- The quantized signals enter a DSP (digital signal processor), where compensation, calibration, angle calculation, and angle/error monitoring are completed. Finally, accurate data is output, and the corresponding output mode can be selected according to the target system.
In addition, the chip integrates core modules such as a low-dropout regulator (LDO), clock oscillator (OSC), electrically erasable programmable memory (EEPROM), and interpolator, achieving a highly integrated design.

Functional Block Diagram
II. Technological Innovation: Making the Complex Simple
The core performance improvement of the MT6620 lies in providing a convenient customer-side self-calibration mode (no data interaction required). It can not only compensate for the offset, amplitude error, and phase error of the sine and cosine input signals caused by installation deviation, but also correct nonlinearity caused by an imperfect magnet, greatly improving INL characteristics. This mode requires continuous motion of the magnetic ring or magnetic scale, but the speed can be non-uniform. The specific steps are as follows:
(1) Install and fix the relative position of the chip and the magnetic ring/magnetic scale;
(2) The magnetic ring must rotate at a speed of 40 pole pairs/min to 3000 pole pairs/min and maintain 16 pole pairs; the magnetic scale must be ensured to run within a speed range of 0.16 m/min to 12 m/min for at least 16 pole pairs;
(3) Pull the CAL-ENB pin low (or write 1 to the 'SOFT-AUTOCAL' register) to make the chip enter the self-calibration state. Then, use the PWM waveform output from the STATUS pin (50% indicates calibrating, 25% indicates calibration failure, and>99% indicates calibration success) or the 'CAL_STATE' register value (0x0 uncalibrated, 0x1 calibrating, 0x2 calibration failed, 0x3 calibration successful) to determine the chip's self-calibration status. After self-calibration succeeds, the chip automatically saves the parameters. Wait ≥500 ms, then pull the CAL-ENB pin high or write 0 to the 'SOFT-AUTOCAL' register to exit self-calibration mode;
(4) If calibration fails, power-cycle the MT6620 and try again.
The MT6620's innovative self-calibration mode reduces system debugging difficulty and helps improve installation efficiency and production yield.
III. Multiple Output Modes for Flexible Adaptation
The MT6620 is like a “social butterfly” in the sensor world, with a rich set of output modes that can adapt to different types of control systems:
- No “generation gap” with traditional control systems—it provides incremental ABZ output similar to conventional optical encoders. The incremental output has a maximum resolution of 2500 pulses per magnetic pole pair, with any integer resolution programmable, or 10000 steps per magnetic pole pair;
- Gets along well with motor control systems—the MT6620 also provides incremental UVW output, with resolution supporting 1 to 63 pole pairs per magnetic pole pair, and any integer pole-pair count programmable;
- Makes friends with simple controllers—PWM output provides 12-bit absolute angle data over a single-wire output, with programmable frequency from 125 Hz to 2 kHz and polarity switchable between active-high and active-low;
- Buddies with digital systems—provides a 3-wire SPI interface for a host computer or MCU to read the chip's internal 16-bit angle data and diagnostic status, and also supports programming operations; SPI timing includes key parameters such as the delay from CSN falling edge to SCK rising edge and the clock period. Data transmission follows a specific protocol and includes CRC verification and a safety word mechanism.
The MT6620 is like a 'multilingual translator,' always finding the right 'language' to communicate with different customer systems. In addition, the chip's built-in EEPROM supports programming over a voltage range of 3.3 V to 5.0 V, with up to 1,000 erase/write cycles and data retention of up to 10 years at 150°C, further enhancing design flexibility.
IV. Outstanding Performance Meets Stringent Requirements
The MT6620 also delivers outstanding performance parameters: angle accuracy reaches ±0.2°, differential nonlinearity (DNL) is ±0.05°, transient noise is only 0.01° RMS, and typical hysteresis window is 0.022°. Its high measurement accuracy enables precise measurement of subtle angle and position changes. In terms of operating environment, the MT6620 can 'endure' high temperatures up to 125°C and 'withstand' extreme cold down to -40°C. Its ESD protection complies with the AEC-Q100 standard—human body model (VHBM) ±4.0 kV and charged device model (VCDM) ±1.0 kV—enabling it to adapt to harsh operating environments. The operating voltage range is 3.3–5.0 V, with an absolute maximum range of 3.0–5.5 V, suitable for various power supply environments; typical operating current is 25 mA, indicating low power consumption. It uses a TSSOP-24 package with compact dimensions (length 7.700–7.900 mm, width 4.300–4.500 mm), combining high integration with ease of installation.
Product Features
| Magnetic Sensing Principle | Hall Array |
| Operating Voltage | 3.3~5.0V |
| Operating Temperature | -40℃~125℃ |
| PWM Output | Yes |
| Digital Interface | SPI |
| ABZ Incremental Output | 1–2500 pulses/magnetic pole pair |
| UVW Incremental Output | 1–63 pole pairs/magnetic pole pair |
| Angle Accuracy | ±0.2° |
| ESD Protection | VHBM:±4.0kV; VCDM:±1.0kV |
| Package | TSSOP-24 |

Package appearance diagram
V. Application Scenarios: Excelling Across Multiple Fields
The MT6620's fixed 2 mm magnetic pole pitch makes it suitable for both off-axis angle detection and linear displacement detection, greatly expanding its application range and giving it broad application prospects in multiple fields.
In intelligent transportation systems, precise angle and position detection is key to ensuring system reliability. The MT6620 is evaluated according to AEC-Q100 standards and can fully meet the intelligent transportation industry's high requirements for accuracy and stability.
In industrial automation, the MT6620 can be used in motor control, robot joint positioning, linear actuator position detection, and other scenarios. For example, in industrial servo systems, its high-resolution incremental ABZ output can replace traditional optical encoders; its high resolution and small package make it particularly suitable for space-constrained applications such as robot joint angle detection.
At electronica China 2024 in Shanghai, MagnTek showcased the MT6620 as a key product, demonstrating the company's emphasis on this product and its competitiveness in the market.
VI. Conclusion: Making Solutions Simpler
With its innovative self-calibration technology, flexible output options, and excellent performance specifications, the MT6620 is an excellent solution for off-axis sensing applications. For users, its self-calibration technology effectively reduces system installation complexity and dependence on mechanical precision, while its excellent performance provides a reliable, precise measurement solution. This embodies the true meaning of technological progress—not making rules more complex, but making solutions simpler.
For more information about the MT6620 or to request samples, please contact NOVOSENSE's official authorized distributor: sales@chiplinkstech.com. WeChat official account: Zhilian Micro - Motor Control Chips. We provide product selection services and technical support, and look forward to working with you.

Sample request attached

WeChat Official Account