0755-82557621 sales@chiplinkstech.com Mon–Fri 09:00–18:00 (UTC+8)
Precision motion control · Components and solutions

SS6625E Brushed Direct-Current Driver Chip: 20V Single H-Bridge, 5.5A Continuous, 16A Peak

For low- and medium-power brushed direct-current motor drive solutions, integrated H-bridge driver chips are widely used in consumer electronics and small electromechanical equipment due to few peripherals, short development cycles, and complete protection. SS6625E is a 20V-grade DC bidirectional motor driver chip with an integrated full H-bridge power MOS circuit, designed for single-channel brushed direct-current motor […]

2026-11-10 Solution Applications
SS6625E有刷直流驱动芯片:20V单H桥,5.5A连续、16A峰值

In low- and medium-power brushed direct-current motor drive solutions, integrated H-bridge driver chips are widely used in consumer electronics and small electromechanical equipment due to advantages such as few peripheral components, short development cycles, and complete protection mechanisms. SS6625E is a 20V-grade DC bidirectional motor driver chip with a complete H-bridge power MOS circuit integrated inside, dedicated to single-channel brushed direct-current motor drive. It can realize four working states: forward rotation, reverse rotation, fast braking, and sleep shutdown, suitable for motor control scenarios in electronic locks, smart toys, small robots, automatic valves, wireless charging mechanisms, and other equipment.

The chip relies on two logic input pins, BI and FI, to complete all motor control. The main controller MCU needs only two general-purpose GPIO to implement all drive logic, reducing hardware wiring and software development work. The chip's own standby current is less than 1μA, resulting in low power consumption when the device is idle, which is friendly to battery-powered products; the power transistor on-resistance RDS (ON) has a typical value of 70mΩ, resulting in low conduction loss.

In terms of drive capability, the chip's maximum continuous output current can reach 5.5A, and the peak current is supported up to 16A, which can handle instantaneous high-current impacts at motor startup and during forward/reverse switching, leaving sufficient current margin for the system. The most typical corresponding scenario is an electronic lock: after the latch bolt reaches position, the motor can no longer turn, and the current will rise all the way to the peak. The peak capability and overcurrent protection of the chip 16A can effectively protect the chip.

The supply operating voltage range is 3.0V to 20V. Power supplies from multiple dry cells to 12 and 18V direct-current power sources can all be adapted, compatible with the supply conditions of most small brushed direct-current motors on the market.

Drive Channels1
Operating Voltage3.0V~20V
Continuous output current5.5A(Max)
Peak output current16A
On-resistance70mΩ
Standby current<1μA
Protection featuresOver-temperature, overcurrent limiting, short circuit
PackageSOP8

The motor is an inductive load, and during startup, shutdown, and commutation, it generates a very high reverse impulse voltage, which can easily damage the driver device. SS6625E integrates freewheeling diodes internally, specifically to release the reverse impulse current generated by the inductive load. There is no need to additionally connect external freewheeling diodes in parallel across the motor, simplifying the peripheral circuit design, while also suppressing interference from the back electromotive force on the chip and the power supply loop.

To address various on-site abnormalities such as stall, short circuit, and overtemperature, the chip integrates a full set of hardware protection mechanisms, including overtemperature protection, overcurrent current-limiting protection, and short-circuit protection. These multiple layers of protection improve long-term operating reliability of the whole machine and reduce the probability of equipment failure and repair.

Pinout View

The chip uses SOP8 surface-mount package. The pin definitions are clear and simple: pin 1 BI and pin 2 FI are logic control inputs; pin 3 GND is power ground; pin 4 VCC is the power supply input; pins 5 and 6 are connected in parallel as FO output; pins 7 and 8 are connected in parallel as BO output; FO and BO can be connected directly to both ends of the direct-current motor to complete wiring.

In actual hardware design, the layout of the power pin filter capacitors is particularly critical. It is recommended to connect 470μF electrolytic capacitor and 0.1μF ceramic capacitor in parallel from VCC to ground, and these two capacitors should be placed as close as possible to the chip's VCC pin. The large-capacity electrolytic capacitor is used to absorb the large energy fed back during motor commutation, while the ceramic capacitor filters out high-frequency noise. Together they stabilize the supply voltage, suppress power supply spikes, and prevent voltage transients from breaking down the chip. High-current traces should be as short and wide as possible, and PCB copper foil should be used for heat dissipation to ensure that heat can be dissipated promptly under high-current operation and avoid triggering overtemperature protection.

Overall, SS6625E combines wide voltage input, high current output, extremely low quiescent power consumption, built-in multiple hardware protections, and simplified peripheral circuits. Whether for battery-powered portable devices or small electromechanical devices powered by adapters, it can provide stable and reliable motor drive capability, making it a cost-effective drive solution for low- and medium-power brushed motor applications.

For more information about SS6625E or to request samples, please contact: sales@chiplinkstech.com; Mr. Chen, 13924675549.

Sample request attached:

WeChat Official Account

← Back to News